u-boot.git/configs/devkit3250_defconfig, branch v2020.10

configs: Resync with savedefconfig

2020-08-10T19:31:07Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig

2020-07-28T20:18:10Z

This converts the following to Kconfig: CONFIG_SPL_NAND_DRIVERS CONFIG_SPL_NAND_ECC CONFIG_SPL_NAND_SIMPLE Signed-off-by: Adam Ford

configs: Resync with savedefconfig

2020-07-06T17:54:25Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_PHYLIB et al to Kconfig

2020-04-28T19:57:58Z

This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2020-01-22T18:38:00Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-12-04T22:18:38Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flash

2019-12-04T18:26:17Z

Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal Reviewed-by: Boris Brezillon [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini

mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND

2019-12-04T04:04:10Z

Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini Reviewed-by: Boris Brezillon

env: Finish migration of common ENV options

2019-11-20T23:32:09Z

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

2019-11-20T17:24:50Z

Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk Cc: Joe Hershberger Signed-off-by: Tom Rini