This converts the following to Kconfig:
   CONFIG_TWL4030_LED
   CONFIG_TWL4030_INPUT

This also removes dead references to:
   CONFIG_TWL4030_KEYPAD

Signed-off-by: Adam Ford <aford173@gmail.com>

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Add a Kconfig option for BOOTP_NTPSERVER to enable the DHCP/BOOTP option
to configure the sntp server address.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS.  As they plainly intended to, set that flag and
re-sync config files.

Signed-off-by: Tom Rini <trini@konsulko.com>

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com>  #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>