The PCIe0 instance of PCIe on the J722S SoC uses the 4 GB Address Window
starting from 0x6_0000_0000 to map System Addresses to PCIe Bus Addresses.
Hence, enable CONFIG_SYS_PCI_64BIT.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133bd ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
Enable PCIe now that it is fixed. Signed-off-by: George McCollister <george.mccollister@konsulko.com> Tested-by: Bryan Brattlof <bb@ti.com>
These are common for all K3 based boards. Add the common values as defaults and remove from each board defconfig Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Bryan Brattlof <bb@ti.com>
Resync all defconfig files using qconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Tested-by: Bryan Brattlof <bb@ti.com>
Acked-by: Peng Fan <peng.fan@nxp.com> #NXP boards
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3 platforms. Since the config value is the same for every board, this patch sets the value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as default for the R5 cores and deletes the instances of SPL_TEXT_BASE in individual defconfigs. Signed-off-by: Anshul Dalal <anshuld@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Siddharth Vadapalli <s-vadapalli@ti.com> says: This series enables USB DFU and USB Mass Storage functionality for AM62, AM62-LP, AM62A, AM62P and J722S SoCs. Link: https://lore.kernel.org/r/20250210112239.2639009-1-s-vadapalli@ti.com
The USB0 instance of USB on J722S SoC is a Designware USB Controller with the same glue layer (wrapper) as AM62 SoC. In order to support USB DFU boot and USB DFU flash with USB0, enable the corresponding glue layer driver. While at it, sync with savedefconfig. Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Judith Mendez <jm@ti.com> says: Some K3 devices like am62x and am64x have a M4 processor in the MCU voltage domain. This patch series introduces remoteproc M4 driver which will be used to load firmware into and start the M4 remote core. This series also adds support for R5F cores on am64x SoCs in patch 2 and sets up environment to load FW in remote cores in patch 3,4,5. This patch series also enables remoteproc drivers by default as per what remoteproc sybsystem is supported per SoC, thus all remoteproc options are now deleted in configs/* since they are no longer required. This patch series was tested on am64x EVM, am62x SK, am62ax SK, am62px SK boards. Any additional tested by's are welcome since I was not able to test any additional boards. Tested by running the following commands in u-boot prompt: => setenv dorprocboot 1 => run boot_rprocs Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig files, remove these configs which are no longer needed to be defined here in configs/. Signed-off-by: Judith Mendez <jm@ti.com> Reviewed-by: Andrew Davis <afd@ti.com>