u-boot.git/configs/mx35pdk_defconfig, branch master

arm: Remove mx35pdk board

2021-02-15T15:11:38Z

This board has not been converted to CONFIG_DM_MMC by the deadline of v2019.04, which is almost two years ago. In addition there are other DM migrations it is also missing. Remove it. Cc: Stefano Babic Signed-off-by: Tom Rini Acked-by: Stefano Babic

configs: Resync with savedefconfig

2020-08-10T19:31:07Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06Z

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

Convert CONFIG_MXC_UART to Kconfig

2020-07-17T12:47:29Z

This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini Acked-by: Peng Fan

configs: Resync with savedefconfig

2020-01-22T18:38:00Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-12-04T22:18:38Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

mtd: ensure MTD is compiled when CMD_MTDPARTS is selected

2019-12-04T18:26:17Z

MTD support must be enabled when using mtdparts. Indeed, functions like get_mtd_info(), get_mtd_device() and put_mtd_device() are in drivers/mtd/mtd_uboot.c and are built only with CONFIG_MTD. Signed-off-by: Miquel Raynal Reviewed-by: Boris Brezillon

mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flash

2019-12-04T18:26:17Z

Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal Reviewed-by: Boris Brezillon [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini

mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND

2019-12-04T04:04:10Z

Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini Reviewed-by: Boris Brezillon

env: Finish migration of common ENV options

2019-11-20T23:32:09Z

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt