u-boot.git/configs/pine64_plus_defconfig, branch v2018.09

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

part: Disable CONFIG_SPL_ISO_PARTITION by default

2018-04-16T22:45:35Z

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf

configs: Resync with savedefconfig

2018-04-08T00:37:13Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Merge git://git.denx.de/u-boot-sunxi

2018-04-04T18:10:39Z

Signed-off-by: Tom Rini

Revert "sunxi: Pine64: temporarily remove extra Pine64 non-plus DT"

2018-04-04T08:45:40Z

Now with the MMC environment gone, we have enough space to accommodate the Pine64 "non-plus" .dtb again. This reverts commit 47952b8e42c2790150e16d3d4235b3a1ee0ba9bb. Signed-off-by: Andre Przywara Reviewed-by: Jagan Teki

Configs: Use the newly added PHY_RTL8211E_PINE64_GIGABIT_FIX

2018-03-22T20:05:27Z

The Pine64+ uses a generic PHY driver, so flip it over to using the Realtek PHY driver to actually apply the RTL8211e fix. Signed-off-by: Kyle Evans Acked-by: Joe Hershberger

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

2018-03-14T05:15:37Z

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence of moving the common definition shared by almost every sunxi board into 123 individual defconfig files. But the U-Boot start address for Allwinner boards is a platform decision which has been around for ages, so defining it in each *board* config file seems a bit over the top. Define the standard values (160MB into DRAM for most SoCs, with two SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from the individual defconfigs. Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki

sunxi: Pine64: temporarily remove extra Pine64 non-plus DT

2018-03-13T14:33:45Z

With the merge of the new u-boot.itb size check now the build for pine64_plus_defconfig breaks, as this file gets too large: ============= u-boot.itb exceeds file size limit: limit: 516096 bytes actual: 521852 bytes excess: 5756 bytes make: *** [u-boot.itb] Error 1 ============= One easily fixable reason is that we actually have two .dtbs in our FIT image, one for the regular Pine64+ board, and one for the non-plus version. The only difference U-Boot cares about is the 100Mbit Ethernet PHY used on the non-plus version, however Ethernet isn't enabled in the non-plus DT anyway. So we could avoid the non-plus special handling, and remove that extra .dtb from the FIT image, which saves a few KBs and brings us back below the limit. The Pine64 would boot with a Pine64+ .dtb, and would fail to enable Ethernet. Given that it didn't work in the first place, this is not a regression. Once we switch to a non-MMC environment, we can bring this back, then with a proper .dtb and hopefully working Ethernet. Signed-off-by: Andre Przywara Signed-off-by: Maxime Ripard

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09Z

On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini