u-boot.git/configs/rock-pi-e-rk3328_defconfig, branch master

env: Rename SYS_MMC_ENV_DEV to ENV_MMC_DEVICE_INDEX

2025-06-20T18:15:08+00:00

Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.

Use ENV_MMC_DEVICE_INDEX to clarify this is the SD/MMC device
index, a number, as enumerated by U-Boot. Update the help text
accordingly.

Signed-off-by: Marek Vasut

env: Rename SYS_RELOC_GD_ENV_ADDR to ENV_RELOC_GD_ENV_ADDR

2025-06-20T18:15:08+00:00

Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.

Reviewed-by: Tom Rini 
Signed-off-by: Marek Vasut

configs: Resync with savedefconfig

2025-05-12T14:52:37+00:00

Resync all defconfig files using qconfig.py

Signed-off-by: Tom Rini

configs: rockchip: enable gpio-leds driver for Radxa boards

2024-10-25T12:46:40+00:00

Basically, Radxa's boards are intended to turn LEDs on at U-Boot.
enable gpio-leds driver and led command.

Signed-off-by: FUKAUMI Naoki 
Reviewed-by: Kever Yang

configs: Resync with savedefconfig

2024-10-08T15:28:10+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

rockchip: rk3328: Migrate to OF_UPSTREAM

2024-05-07T07:56:10+00:00

All RK3328 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.

Migrate all RK3328 boards to use OF_UPSTREAM.

Signed-off-by: Jonas Karlman 
Reviewed-by: Kever Yang

rockchip: Migrate to use DM_USB_GADGET on RK3328

2024-03-14T10:19:27+00:00

USB gadget is not working fully as expected on RK3328, it uses a
board_usb_init() function to initialize the DWC2 OTG port.

The board_usb_init() function does not intgrate with the generic phy
framework and as a result the USB phy is not properly configured before
or after USB gadget use.

Having both USB_DWC2 and DWC2_OTG enabled for the same board is also
causing some issues.

Trying to use rockusb or ums command after usb stop result in a freeze
due to usb stop is putting the phy in a suspended state.

  => usb start
  => usb stop
  => ums 0 mmc 0
  --> freeze due to usb phy is suspended <--

Fix this by only using one of USB_DWC2 (host) or DWC2_OTG (peripheral)
depending on the most likely usage of the otg port and by migrating to
use DM_USB_GADGET instead of a board_usb_init() function.

The nanopi-r2 and orangepi-r1-plus variants share OTG and power using a
Type-C connector, mark these boards dr_mode as peripheral, the most
likely usage is for recovery and image download.

The rock64 and roc-cc currently use dr_mode as host, remove the DWC2_OTG
driver from these boards to ensure that the USB_DWC2 driver is used.

The rock-pi-e board does not enable the usb20_otg node so both USB_DWC2
and DWC2_OTG is removed from this board.

Enable RockUSB and UMS on all boards with a otg port in peripheral mode.

Also with the migration to DM_USB_GADGET completed the U-Boot specific
change to reorder usb nodes in the soc device tree can be reverted.

Signed-off-by: Jonas Karlman 
Reviewed-by: Kever Yang

rockchip: Use common bss and stack addresses on RK3328

2024-03-14T07:27:28+00:00

With the stack and text base used by U-Boot SPL and proper on RK3328
there is a high likelihood of overlapping when U-Boot proper + FDT nears
or exceeded 1 MiB in size.

Currently the following memory layout is typically used on RK3328:
[    0, 256K) - SPL binary
[ 256K,   2M) - TF-A / reserved
[   2M,   +X) - U-Boot proper binary (TEXT_BASE)
[   -X,   3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[  -8K,   3M)   - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[   -X,   4M) - SPL pre-reloc stack (SPL_STACK)
[  -8K,   4M)   - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[   -X,   6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[   5M,   6M)   - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[  32M,  +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)

SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout.
However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is
restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.

Migrate to use common bss, stack and malloc heap size and addresses to
fix this restriction and allow for a larger U-Boot proper image size.

Signed-off-by: Jonas Karlman 
Reviewed-by: Kever Yang

rockchip: rk3328: regenerate defconfigs

2024-03-14T03:48:40+00:00

Regenerate RK3328 defconfigs after adding imply statements.

Signed-off-by: Chen-Yu Tsai 
Reviewed-by: Christopher Obbard 
Reviewed-by: Dragan Simic

rockchip: rk3328-rock-pi-e: Update defconfig

2024-03-14T03:40:48+00:00

Update defconfig for rk3328-rock-pi-e with new defaults.

Remove the xPL_DRIVERS_MISC=y option, no misc driver is used in xPL.

Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.

Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.

Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.

Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.

Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.

Add DM_MDIO=y to ensure device tree props can be used by PHY driver.

Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.

Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.

Also add myself as a reviewer for this board.

Signed-off-by: Jonas Karlman 
Reviewed-by: Kever Yang 
Reviewed-by: Kever Yang