u-boot.git/configs/slimbootloader_defconfig, branch v2022.01

net: convert TFTP_TSIZE to proper Kconfig option

2021-06-09T01:38:51Z

TFTP transfer size can be used to re-size the TFTP progress bar on single line based on the server reported file size. The support for this has been around from 2019, but it was never converted to proper Kconfig. While adding this new Kconfig, enable it by default for OMAP2+ and K3 devices also. Signed-off-by: Tero Kristo

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06Z

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2020-07-28T12:46:52Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_BZIP2 et al to Kconfig

2020-06-04T22:10:02Z

This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09Z

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

2019-11-20T17:24:50Z

Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk Cc: Joe Hershberger Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-11-07T22:58:06Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

x86: Change condition for using CAR

2019-10-08T05:57:36Z

At present we assume that CAR (Cache-as-RAM) is used if HOBs (Hand-off blocks) are not, since HOBs typically indicate that an FSP is in use, and FSPs handle the CAR init. However this is a bit indirect, and for FSP2 machines which use their own CAR implementation (such as apollolake) but use the FSP for other functions, the logic is wrong. To fix this, add a dedicated Kconfig option to indicate when CAR is used. Signed-off-by: Simon Glass Reviewed-by: Bin Meng [bmeng: fix a typo in the commit message] Signed-off-by: Bin Meng

configs: Resync with savedefconfig

2019-08-14T12:11:27Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

board: intel: Add new slimbootloader board

2019-08-09T14:24:02Z

Add slimbootloader board to run U-boot as a Slim Bootloader payload - Add new board/intel/slimbootloader directory with minimum codes - Add slimbootloader configuration files - Add doc/board/intel/slimbootloader.rst Signed-off-by: Aiden Park Reviewed-by: Bin Meng Reviewed-by: Andy Shevchenko Tested-by: Bin Meng [bmeng: add slimbootloader board MAINTAINERS file] Signed-off-by: Bin Meng