u-boot.git/configs/sniper_defconfig, branch master

env: Rename SYS_RELOC_GD_ENV_ADDR to ENV_RELOC_GD_ENV_ADDR

2025-06-20T18:15:08+00:00

Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.

Reviewed-by: Tom Rini 
Signed-off-by: Marek Vasut

configs: Resync with savedefconfig

2024-10-08T15:28:10+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

spl: mmc: Try to clean up raw-mode options

2024-08-23T21:58:41+00:00

Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.

There are three different ways of specifying the offset:

- sector offset
- partition number
- partition type

So make these a choice, so it is more obvious what is going on.

Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.

Reviewed-by: Sean Anderson 
Reviewed-by: Quentin Schulz 
Signed-off-by: Simon Glass

omap3: sniper: Convert to device-tree control and DM I2C

2024-08-07T00:33:17+00:00

This converts the sniper board (LG P970) to device-tree control
and DM I2C, both for SPL and U-Boot.

Note that we lose the call to board_mmc_power_init to enable power
for MMC2. This is now expected to take place through proper
regulators, which are not yet available with the twl4030 driver.
The call to twl4030_power_mmc_init is moved to spl_board_init for now.

Signed-off-by: Paul Kocialkowski

omap3: sniper: Streamline defconfig

2024-08-07T00:32:46+00:00

Remove custom config options that are not particularly necessary.
Align them with OMAP3 defaults used on other boards (especially for
memory locations).

Also enable Thumb build to reduce the SPL size and remove the custom
prompt text.

This makes the config a lot more minimalistic, maintainable and easier
to read.

Signed-off-by: Paul Kocialkowski 
Reviewed-by: Tom Rini 
Tested-by: Derald D. Woods

omap3: Define DRAM banks number in Kconfig instead of defconfigs

2024-08-07T00:32:45+00:00

The number of DRAM banks was defined to the same value in each OMAP3
board defconfig, which is expected and hardcoded in the code. Move the
common definition to the Kconfig option declaration instead.

Signed-off-by: Paul Kocialkowski 
Reviewed-by: Tom Rini 
Tested-by: Derald D. Woods

omap3: Define maximum SPL size in Kconfig instead of defconfigs

2024-08-07T00:32:45+00:00

The maximum SPL size was defined to the same value in each OMAP3
board defconfig. Move the common definition to the Kconfig option
declaration instead.

Signed-off-by: Paul Kocialkowski 
Reviewed-by: Tom Rini 
Tested-by: Derald D. Woods

omap3: Define common init stack pointer address in Kconfig

2024-08-07T00:32:45+00:00

The init stack pointer was defined to the same value in each OMAP3
board defconfig. Move the common definition to the Kconfig option
declaration instead.

Signed-off-by: Paul Kocialkowski 
Reviewed-by: Tom Rini 
Tested-by: Derald D. Woods

omap3: Define common SPL text base in Kconfig instead of defconfigs

2024-08-07T00:32:45+00:00

The SPL text base was defined to the same value in each OMAP3 board
defconfig. Move the common definition to the Kconfig option
declaration instead.

Signed-off-by: Paul Kocialkowski 
Tested-by: Adam Ford  #am3517-evm
Reviewed-by: Tom Rini 
Tested-by: Derald D. Woods

configs: Resync with savedefconfig

2024-04-22T23:40:37+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini