u-boot.git/configs/tec_defconfig, branch v2016.01

ns16550: move CONFIG_SYS_NS16550 to Kconfig

2015-11-22T02:50:18Z

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py. Signed-off-by: Thomas Chou

common: add CMD_GPIO to Kconfig

2015-11-18T19:50:06Z

Add CMD_GPIO to Kconfig and run tools/moveconfig.py . Signed-off-by: Thomas Chou Reviewed-by: Simon Glass

Reorder defconfigs with 'savedefconfig'

2015-09-28T13:06:13Z

Some boards' defconfigs are disordered. Reorder them. Signed-off-by: Bin Meng

kconfig: add config option for shell prompt

2015-08-13T11:19:33Z

Add option to set shell prompt string from menuconfig and migrate boards globally. The migration is done as follows: - Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the entry moved to their defconfig files. - Boards that defined some kind of #ifdef logic which selects the CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT right before the #ifdef logic and were left alone. - This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus CONFIG_SYS_PROMPT was removed from all _common.h and _common.h files. This results in a streamlined default value across platforms, and includes the following files: spear-common, sunxi-common, mv-common, ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common. - Boards that relied on _common.h values of CONFIG_SYS_PROMPT were not updated in their respective defconfig files under the assumption that since they did not explicitly define a value, they're fine with whatever the default is. - On the other hand, boards that relied on a value defined in some _common.h file such as woodburn_common, rpi-common, bur_am335x_common, ls2085a_common, siemens_am33x_common, and omap3_evm_common, had their values moved to the respective defconfig files. - The define V_PROMPT was removed, since it is not used anywhere except for assigning a value for CONFIG_SYS_PROMPT. Cc: Tom Rini Cc: Masahiro Yamada Cc: Stefano Babic Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov [trini: Add spring, sniper, smartweb to conversion] Signed-off-by: Tom Rini

Move defaults from config_cmd_default.h to Kconfig

2015-06-26T02:18:34Z

This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini

Move default y configs out of arch/board Kconfig

2015-06-26T02:17:55Z

Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini

net: Move the CMD_NET config to defconfigs

2015-06-01T14:40:15Z

This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger

kconfig: remove meaningless prefixes in defconfig files

2015-03-15T18:31:06Z

Since commit e02ee2548afe (kconfig: switch to single .config configuration), the prefixes in defconfig files such as "+S:", "+ST:", etc., are meaningless. This commit was generated by the following command: find configs -name '*_defconfig' | xargs sed -i 's/^+*S*T*://' Signed-off-by: Masahiro Yamada

kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig

2014-09-25T13:31:24Z

This option specifies the default Device Tree used for the run-time configuration of U-Boot. Signed-off-by: Masahiro Yamada Cc: Simon Glass Cc: Stephen Warren Cc: Minkyu Kang Cc: Michal Simek

tegra: kconfig: move board select menu and common settings

2014-08-31T01:19:32Z

Becuase the board select menu in arch/arm/Kconfig is too big, move the Tegra board select menu to tegra/Kconfig. Insert the Tegra SoC select menu between the arch select and the board select. Architecture select |-- Tegra Platform (Tegra) |- Tegra SoC select (Tegra20 / 30 / 114 / 124) |- Board select Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows: config TEGRA bool select SPL Signed-off-by: Masahiro Yamada Acked-by: Stephen Warren Cc: Tom Warren