u-boot.git/configs, branch v2016.11

igep00x0: consolidate defconfigs

2016-11-13T20:54:34+00:00

Defconfigs should remain the same except CONFIG_SYS_EXTRA_OPTIONS.
Drop NAND specific defconfig as flash type is runtime detected.

Signed-off-by: Ladislav Michl 
Reviewed-by: Javier Martinez Canillas

igep00x0: disable CONFIG_DISPLAY_BOARDINFO

2016-11-13T20:54:34+00:00

As a single U-Boot binary can now run on various board modifications,
drop CONFIG_DISPLAY_BOARDINFO as it prints flash memory information
too early to give us chance to easily detect it. Also saves few bytes
as a bonus.

Signed-off-by: Ladislav Michl 
Reviewed-by: Javier Martinez Canillas 
Tested-by: Javier Martinez Canillas

ARM: tegra: enable Ethernet on p2771-0000

2016-11-07T17:28:16+00:00

Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.

Signed-off-by: Stephen Warren 
Reviewed-by: Simon Glass 
Acked-by: Joe Hershberger

rk3288: config change for enable dram capacity auto-detect.

2016-10-30T19:29:06+00:00

Enable ROCKCHIP_SPL_BACK_TO_BROM and disable CONFIG_SPL_MMC_SUPPORT
to save memory in order to enable add source code for dram capacity
auto-detect.

Signed-off-by: Kever Yang

sunxi: Add support for Cubieboard4

2016-10-30T10:38:05+00:00

The Cubieboard4 is an A80 SoC based development board from Cubietech.

This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector,
HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT
combo chip, headphone and microphone jacks, IR receiver, and GPIO headers.

Signed-off-by: Chen-Yu Tsai 
Acked-by: Hans de Goede 
Signed-off-by: Hans de Goede

sunxi: Enable SPL support for A80 Optimus board

2016-10-30T10:38:04+00:00

The A80 Optimus Board was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.

This board has a UART port, a JTAG connector, 2 USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash,
2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.

Signed-off-by: Chen-Yu Tsai 
[hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig
 instead of adding a new defconfig]
Acked-by: Hans de Goede 
Signed-off-by: Hans de Goede

sunxi: A64: enable USB support

2016-10-30T10:38:04+00:00

Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]

Signed-off-by: Amit Singh Tomar 
Signed-off-by: Andre Przywara 
Reviewed-by: Hans de Goede 
Signed-off-by: Hans de Goede

sunxi: Update DRAM clock for Olimex A20 boards

2016-10-30T10:38:04+00:00

Originally dram clock was set to 480MHz, but this behaves
unstable. To improve stability the clock is reduced to 384MHz

Signed-off-by: Stefan Mavrodiev 
Reviewed-by: Hans de Goede 
Signed-off-by: Hans de Goede

configs/chromebox_panther_defconfig: Re-enable CONFIG_DM_PCI

2016-10-29T13:00:01+00:00

This was turned off by accident, re-enble.

Signed-off-by: Tom Rini

Merge branch 'master' of git://git.denx.de/u-boot-atmel

2016-10-28T18:14:18+00:00