u-boot.git/configs, branch v2021.07

Merge tag 'u-boot-amlogic-20210703' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

2021-07-02T22:56:46Z

- configs: libretech: set SPI mode to 0 to fix SPI NOR Flash probe

configs: libretech: set SPI mode to 0

2021-07-02T21:59:27Z

Kconfig defaults to mode 3 if CONFIG_SF_DEFAULT_MODE is not set. It becomes an issue since meson_spifc does not support SPI_CPHA. Needed after commit e2e95e5e25 ("spi: Update speed/mode on change"). Fixes: e2e95e5e25 ("spi: Update speed/mode on change") Signed-off-by:Da Xue [narmstrong: reformated commit reference & added Fixes tag] Signed-off-by: Neil Armstrong

efi_loader: Force a single FMP instance per hardware store

2021-07-02T07:37:01Z

Chapter 23 of the EFI spec (rev 2.9) says: "A specific updatable hardware firmware store must be represented by exactly one FMP instance". This is not the case for us, since both of our FMP protocols can be installed at the same time because they are controlled by a single 'dfu_alt_info' env variable. So make the config options depend on each other and allow the user to install one of them at any given time. If we fix the meta-data provided by the 'dfu_alt_info' in the future, to hint about the capsule type (fit or raw) we can revise this and enable both FMPs to be installed, as long as they target different firmware hardware stores Note that we are not using a Kconfig 'choice' on purpose, since we want to allow both of those to be installed and tested in sandbox Signed-off-by: Ilias Apalodimas Reviewed-by: Heinrich Schuchardt

configs: Resync with savedefconfig

2021-06-28T14:17:29Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

imx8mm: configs: enable distro default features

2021-06-21T11:35:23Z

imx8mm ekv has been switched to use distro boot commands, but had no correct options enabled to support sysboot. According to the README.distro, sysboot is consindered to be a recommended way of using distro boot commands, it required default distro features to be enabled instead of only those that are relevant to the boot script. Replace the boot script specific options in the config to a default distro option. Signed-off-by: Andrey Zhizhikin Cc: Peng Fan Fixes: 2df8930bf9 ("imx8mm: configs: add support for distro boot commands") Reviewed-by: Fabio Estevam

imx8mp: configs: enable distro default features

2021-06-21T11:33:55Z

imx8mp ekv has been switched to use distro boot commands, but had no correct options enabled to support sysboot. According to the README.distro, sysboot is consindered to be a recommended way of using distro boot commands, it required default distro features to be enabled instead of only those that are relevant to the boot script. Replace the boot script specific options in the config to a default distro option. Signed-off-by: Andrey Zhizhikin Cc: Peng Fan Fixes: 9b162b1d1f ("imx8mp: configs: add support for distro boot commands") Reviewed-by: Fabio Estevam

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq

2021-06-17T12:44:56Z

- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release, mmc, usb, env, etc for Layerscape boards - powerpc: Update Maintainers for some boards.

board: freescale: t208xrdb: add a config option for rev D dts fixups

2021-06-17T06:16:11Z

Under DM, we rely on u-boot's device tree to provide the correct PHY addresses. The board_fix_fdt callback is intended to be used for device tree fixups before relocation. Unfortunately, this isn't an option when booting from flash since the device tree isn't writable before relocation. This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a board revision D or up is the target. The config option is used to set the correct Aquantia PHY address in the board's u-boot device tree. Defconfig files with the option enable explicitly are added for convenience. Signed-off-by: Camelia Groza Reviewed-by: Priyanka Jain

board/km: add support for expu1 design based on nxp

2021-06-17T06:16:11Z

The EXPU1 design is a new 40G capable ethernet service unit card for Hitachi-Powergrids wired-com product lines. The base SoC is same as for already added SELI8 card, consequently the already added u-boot support for SELI8 is reused. Signed-off-by: Rainer Boschung Signed-off-by: Aleksandar Gerasimovski [Fixed new line error at EOF] Signed-off-by: Priyanka Jain

configs: seli8: set envsize to 0x4000

2021-06-17T06:16:11Z

During the mainlining of the board this was by mistake set to sector size. Our user space env scripts are expecting envsize of 0x4000, and setting this differently will break our cross-platform compatibility. Signed-off-by: Aleksandar Gerasimovski Reviewed-by: Priyanka Jain