Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

The s3c6400.h file is only for S3C64XX cpu and the pheripheral port
address(0x70000000 - 0x7fffffff) exists at only S3C64XX cpu, so they
should be included by only S3C64XX cpu.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

According to the PPC reference implementation the udelay() function is
responsible for resetting the watchdog timer as frequently as needed.
Most other architectures do not meet that requirement, so long-running
operations might result in a watchdog reset.

This patch adds a generic udelay() function which takes care of
resetting the watchdog before calling an architecture-specific
__udelay().

Signed-off-by: Ingo van Lil <inguin@gmx.de>

Fix stack_setup to place the stack on the correct address in DRAM
accroding to U-Boot standard and remove conditional compilation by
CONFIG_MEMORY_UPPER_CODE macro that is not necessry. This macro
was introduced and used only by this board for some unclear reason.

The definition of this macro is also removed because it's not
referenced elsewhere.

Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>

This patch moves the s3c64xx header files from include/
to include/asm-arm/arch-s3c64xx

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

-fno-strict-aliasing is hidding warnings.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

For some time there have been repeated reports about build problems
with some ARM (cross) tool chains.  Especially issues about
(in)compatibility with the tool chain provided runtime support
library libgcc.a caused to add and support a private implementation
of such runtime support code in U-Boot.  A closer look at the code
indicated that some of these issues are actually home-made.  This
patch attempts to clean up some of the most obvious problems and make
building of U-Boot with different tool chains easier:

- Even though all ARM systems basicy used the same compiler options
  to select a specific ABI from the tool chain, the code for this was
  distributed over all cpu/*/config.mk files.  We move this one level
  up into lib_arm/config.mk instead.

- So far, we only checked if "-mapcs-32" was supported by the tool
  chain; if yes, this was used, if not, "-mabi=apcs-gnu" was
  selected, no matter if the tool chain actually understood this
  option.  There was no support for EABI conformant tool chains.
  This patch implements the following logic:

  1) If the tool chain supports
	"-mabi=aapcs-linux -mno-thumb-interwork"
     we use these options (EABI conformant tool chain).
  2) Otherwise, we check first if
	"-mapcs-32"
     is supported, and then check for
	"-mabi=apcs-gnu"
     If one test succeeds, we use the first found option.
  3) In case 2), we also test if "-mno-thumb-interwork", and use
     this if the test succeeds. [For "-mabi=aapcs-linux" we set
     "-mno-thumb-interwork" mandatorily.]

  This way we use a similar logic for the compile options as the
  Linux kernel does.

- Some EABI conformant tool chains cause external references to
  utility functions like raise(); such functions are provided in the
  new file lib_arm/eabi_compat.c

  Note that lib_arm/config.mk gets parsed several times, so we must
  make sure to add eabi_compat.o only once to the linker list.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Dirk Behme <dirk.behme@googlemail.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Tested-by: Andrzej Wolski <awolski@poczta.fm>
Tested-by: Gaye Abdoulaye Walsimou <walsimou@walsimou.com>
Tested-by: Tom Rix <Tom.Rix@windriver.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)

that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>