u-boot.git/cpu/arm920t/start.S, branch master

arm: Move cpu/$CPU to arch/arm/cpu/$CPU

2010-04-13T07:13:24+00:00

Signed-off-by: Peter Tyser

Add a unified s3c24x0 header file

2009-11-27T22:26:13+00:00

This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.

Signed-off-by: Kevin Morfitt 
Signed-off-by: Minkyu Kang

Clean-up of cpu_arm920t and cpu_arm920t_s3c24x0 code

2009-10-14T02:13:56+00:00

This patch re-formats the code in cpu/arm920t and cpu/arm920t/23c24x0 in
preparation for changes to add support for the Embest SBC2440-II Board.

The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
  non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports

It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009

Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets and no
new warnings or errors were found.

Signed-off-by: Kevin Morfitt 
Signed-off-by: Minkyu Kang

cpu/arm920t/start.S: include to have ROUND() defined

2009-07-27T08:06:39+00:00

Commit fcd3c87e made include/common.h usable by assembler code but
failed to update cpu/arm920t/start.S

Signed-off-by: Wolfgang Denk

Fix e-mail address of Gary Jennejohn.

2009-05-15T20:11:59+00:00

Signed-off-by: Detlev Zundel

Add support for the AT91RM9200EK Board.

2009-04-04T18:42:20+00:00

The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)

Signed-off-by: Ulf Samuelsson 
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

AT91: remove non supported board AT91RM9200DF macro

2008-12-02T20:59:29+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

AT91RM9200DK: fix broken boot from NOR flash

2008-11-24T21:10:07+00:00

Signed-off-by: Wolfgang Denk

at91rm9200: fix broken boot from nor flash

2008-11-24T21:10:04+00:00

This patch fix the broken boot from NOR Flash on AT91RM9200 boards, if
CONFIG_AT91RM9200 is defined and nor preloader is used.

Signed-off-by: Jens Scharsig

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD