u-boot.git/cpu/arm926ejs/davinci/Makefile, branch v2009.08

Moved Davinci Ethernet driver to drivers/net

2009-06-15T07:13:54Z

This driver has been renamed davinci_emac.c Signed-off-by: Ben Warren

davinci: display correct clock info

2009-06-12T18:39:49Z

Move the clock-rate dumping code into the cpu/.../davinci area where it should have been, enabled by CONFIG_DISPLAY_CPUINFO, updating the format and showing the DSP clock (where relevant). Switch boards to use the cpuinfo() hook for this stuff. Remove a few now-obsolete PLL #defines. Signed-off-by: David Brownell

davinci: add basic dm355/dm350/dm335 support

2009-06-12T18:39:48Z

Add some basic declarations for DaVinci DM355/DM350/DM335 support, keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the DM357 is very different; while the DM355 is like a DM355 without the MPEG/JPEG coprocessor). These have different peripherals than the DM6446, and some of the peripherals are at different addresses. Notably for U-Boot, there's no EMAC, and the NAND controller address is different Signed-off-by: David Brownell

davinci: split out some dm644x-specific bits from psc

2009-06-12T18:39:48Z

Split out DaVinci DM6446-specific bits from more generic bits: - Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips; DM6443 and DM6441 chips differ in available peripherals. - Move most DM644X-specific bits from psc.c to a new dm644x.c file, which is conditionally built. It provides device-specific setup. Plus minor coding style and comment updates with respect to the PSC. Signed-off-by: David Brownell

davinci: cpu-specific build uses conditional make syntax

2009-06-12T18:39:47Z

Update cpu/arm926ejs/davinci/Makefile to use COBJ-y type syntax. Add the first conditional: for EMAC driver support. Not all chips have an EMAC; and boards might not use it, anyway. This doesn't touch PHY configuration; that should eventually become conditional too. Signed-off-by: David Brownell

davinci: move psc support board-->cpu

2009-06-12T18:39:47Z

Move DaVinci PSC support from board/* to cpu/* where it belongs. The PSC module manages clocks and resets for all DaVinci-family SoCs, and isn't at all board-specific. Signed-off-by: David Brownell

DaVinci now respects SKIP_LOWLEVEL_INIT

2009-06-12T18:39:47Z

Don't needlessly include lowlevel init code; that's only really needed with boot-from NOR (not boot-from-NAND). The 2nd stage loader (UBL) handles that before it loads U-Boot. Signed-off-by: David Brownell

davinci: move i2c driver to drivers/i2c

2009-03-30T16:58:39Z

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

davinci: move nand driver to drivers/mtd/nand

2009-03-30T16:58:39Z

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

[ARM] TI DaVinci support, hopefully final

2007-08-10T18:26:18Z

Add support for the following DaVinci boards: - DV_EVM - SCHMOOGIE - SONATA Changes: - Split into separate board directories - Removed changes to MTD_DEBUG (or whatever it's called) - New CONFIG_CMD party line followed - Some cosmetic fixes, cleanup etc. - Patches against the latest U-Boot tree as of now. - Fixed CONFIG_CMD_NET in net files. - Fixed CONFIG_CMD_EEPROM for schmoogie. - Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and DV_EVM. Can't check if it works on SONATA, don't have a board any more, but it at least compiles. Here is an excerpt from session log on SCHMOOGIE... U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17) DRAM: 128 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock : 297MHz DDR Clock : 162MHz ETH PHY : DP83848 @ 0x01 U-Boot > iprobe Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F U-Boot > ping 192.168.253.10 host 192.168.253.10 is alive U-Boot > Signed-off-by: Sergey Kubushyn Acked-by: Dirk Behme Acked-by: Zach Sadecki Acked-by: Stefan Roese