u-boot.git/cpu/arm926ejs, branch v2009.08-rc2

mxc-mmc: sdhc host driver for MX2 and MX3 proccessor

2009-08-09T21:47:38+00:00

This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.

Signed-off-by: Ilya Yanok

Add AT91SAM9260 to at91's lowlevel_init.S

2009-08-01T09:45:05+00:00

Needed for AT91SAM9260 NOR Boot on Eukrea's CPU9260.

Signed-off-by: Eric Benard

arm nomadik: add gpio support

2009-07-29T07:57:46+00:00

Signed-off-by: Alessandro Rubini 
Acked-by: Andrea Gallo 
Acked-by: Jean-Christophe PLAGNIOL-VILLARD

Make include/common.h usable by assembler code

2009-07-26T22:12:32+00:00

Commit 70ebf316 factored out the ROUND() macro into include/common.h,
not realizing that the primary use of this macro on AT91 systems was
in start.S where common.h was not included, and could not be included
because it contains a lot of C code which the assembler doesn't
understand.

This patch wraps such code in common.h in a "#ifndef __ASSEMBLY__"
construct, and then adds an include to cpu/arm926ejs/start.S thus
solving the problem.

Signed-off-by: Wolfgang Denk

fec_mxc: driver for FEC ethernet controller on i.MX27

2009-07-23T05:59:07+00:00

Signed-off-by: Ilya Yanok 
Signed-off-by: Ben Warren

at91: Introduction of at91sam9g10 SOC.

2009-07-12T15:56:11+00:00

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Signed-off-by: Sedji Gaouaou

at91: Introduction of at91sam9g45 SOC.

2009-07-12T15:43:34+00:00

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou

Coding style cleanup; update CHANGELOG

2009-07-07T20:35:02+00:00

Signed-off-by: Wolfgang Denk

arm: Kirkwood: arch specific updated for ehci-Kirkwood driver support

2009-07-06T19:53:15+00:00

This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver

Signed-off-by: Prafulla Wadaskar

arm nomadik: use 1000 as HZ value and rewrite timer code

2009-07-06T19:53:08+00:00

This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller.  Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.

Signed-off-by: Alessandro Rubini 
Acked-by: Andrea Gallo 
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD