u-boot.git/cpu/at32ap, branch v2009.01

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Add support for the hammerhead (AVR32) board

2008-07-30T08:06:11+00:00

The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel.  It offers versatile peripherals, such as ethernet, usb
device, usb host etc.

The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).

Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.

For more information see: http:///www.miromico.com/hammerhead

Signed-off-by: Julien May 
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen

mmc: Move atmel_mci driver into drivers/mmc

2008-07-09T22:05:52+00:00

This makes it easier to use the driver on other platforms.

Signed-off-by: Haavard Skinnemoen 
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD

avr32: Use CONFIG_ATMEL_MCI to select the atmel_mci driver

2008-07-09T22:04:47+00:00

After we move the atmel_mci driver into drivers/mmc, we can't select
it with CONFIG_MMC anymore. Introduce a new symbol specifically for
this driver so that there's no ambiguity.

Signed-off-by: Haavard Skinnemoen 
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD

Merge branch 'master' of git://www.denx.de/git/u-boot-avr32

2008-07-06T22:39:43+00:00

MMC: Consolidate MMC/SD command definitions

2008-06-28T20:40:15+00:00

This moves the MMC and SD Card command definitions from
include/asm/arch/mmc.h into include/mmc.h. These definitions are
given by the MMC and SD Card standards, not by any particular
architecture.

There's a lot more room for consolidation in the MMC drivers which
I'm hoping to get done eventually, but this patch is a start.

Compile-tested for all avr32 boards as well as lpc2292sodimm and
lubbock. This should cover all three mmc drivers in the tree.

Signed-off-by: Haavard Skinnemoen

avr32: Fix SPI portmux initialization

2008-06-20T10:46:43+00:00

Use the new GPIO manipulation functions to set up the chip select lines,
and make sure both busses use GPIO for chip select control.

Signed-off-by: Haavard Skinnemoen

avr32: Add GPIO manipulation functions

2008-06-20T08:40:42+00:00

Adds GPIO manipulation functions for AVR32 AP7 platform.

Signed-off-by: Peter Ma 
[haavard.skinnemoen@atmel.com: coding style fixup, slight simplification]
Signed-off-by: Haavard Skinnemoen

atmel_spi: Driver for the Atmel SPI controller

2008-06-03T18:30:05+00:00

This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.

Changed in v4:
  - Update to new API
  - Handle zero-length transfers appropriately. The user may send a
    zero-length SPI transfer with SPI_XFER_END set in order to
    deactivate the chip select after a series of transfers with chip
    select active. This is useful e.g. when polling the status
    register of DataFlash.

Signed-off-by: Haavard Skinnemoen

avr32: Fix theoretical race in udelay()

2008-05-27T13:27:31+00:00

If the specified delay is very short, the cycle counter may go past the
"end" time we are waiting for before we get around to reading it.

Fix it by checking the different between the cycle count "now" and the
cycle count at the beginning. This will work as long as the delay
measured in number of cycles is below 2^31.

Signed-off-by: Haavard Skinnemoen