u-boot.git/cpu/mpc83xx/cpu_init.c, branch v2009.06

mpc83xx: correctly set encryption and I2C bus 0 clock

2009-03-14T22:43:58+00:00

This patch makes sure the correct mask is applied when setting
the encryption and I2C bus 0 clock in SCCR.
Failing to do so may lead to ENCCM being 0 in which case I2C bus 0
won't function.

Signed-off-by: Norbert van Bolhuis 
Signed-off-by: Kim Phillips

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

mpc83xx: Store and display Arbiter Event Register values

2008-09-03T21:06:57+00:00

Record the Arbiter Event Register values and optionally display them.

The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.

Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
 #define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
                                    and type register values
 #define CONFIG_DISPLAY_AER_FULL  - display and interpret the arbiter
                                    event register values

Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
 #define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
                              only events, so that it can still capture
                              other real problems.

Signed-off-by: Nick Spence 
Signed-off-by: Kim Phillips

MPC83XX: Fix GPIO configuration - set gpio level before direction

2008-09-03T21:06:46+00:00

Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.

Set gpio level register before direction register to inhibit
glitches on high level output pins.

Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.

Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.

Signed-off-by: Nick Spence 
Signed-off-by: Peter Korsgaard 
Signed-off-by: Kim Phillips

fix system config overwrite @ MPC834x and MPC8313

2008-06-25T22:04:28+00:00

During 83xx setup the "System I/O configuration register high" gets
overwritten with user defined value if CFG_SICRH is defined.

Regarding to the MPC834x manual (Table 5-28 reve.1) bits 28+29 of SICRH
must keep their reset value regardless of configuration.

On my board (using RGMII) those bits are set after reset - yet it's
unclear where they come from.

The patch keeps both bits on MPC834x and MPC8313.

Signed-off-by: Andre Schwarz 
Signed-off-by: Kim Phillips

Big white-space cleanup.

2008-05-20T22:14:08+00:00

This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk

mpc8323erdb: Improve the system performance

2008-03-26T00:16:44+00:00

The following changes are based on kernel UCC ethernet performance:

1.  Make the CSB bus pipeline depth as 4, and enable the repeat mode
2.  Optimize transactions between QE and CSB.  Added CFG_SPCR_OPT
    switch to enable this setting.

The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:

3.  CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4.  CS0_CONFIG[ODT_WR_CONFIG] set to 1.  Was a reserved setting
    previously.
5.  TIMING_CFG_1[WRREC] is changed from 3clks to 2clks  (based on
    Twr=15ns, and this was already the setting in DDR_MODE)
6.  TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
    Trp=15ns)
7.  TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
    Tras=40ns)
8.  TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
    Trcd=15ns)
9.  TIMING_CFG_1[REFREC] changed from 21 clks to 11clks.  (based on
    Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks.  (based
    on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
    on CL=3 and WL=2).

Signed-off-by: Michael Barkowski 
Acked-by: Kim Phillips

mpc83xx: Fix the fatal conflict of merge

2008-01-17T17:01:52+00:00

The commit 9e89647889cd4b5ada5b5e7cad6cbe55737a08d7
will cause the mpc8315erdb board can't boot up.

The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.

Signed-off-by: Dave Liu 
Signed-off-by: Kim Phillips

mpc83xx: add support for more system clock performance controls

2008-01-16T18:32:39+00:00

System registers that are modified are the Arbiter Configuration
Register (ACR), the System Priority Control Register (SPCR), and the
System Clock Configuration Register (SCCR).

Signed-off by: Michael F. Reiss 
Signed-off by: Joe D'Abbraccio 
Signed-off-by: Kim Phillips

mpc83xx: Add config of eTSEC emergency priority in SPCR

2008-01-16T18:00:49+00:00

The TSEC emergency priority definition of 831x/837x
is different than the definition of 834x in SPCR register.

Add the other config of TSEC emergency priority into
cpu_init.c

Signed-off-by: Dave Liu 
Signed-off-by: Kim Phillips