u-boot.git/doc/README.at91, branch v2016.09

ARM: at91: add NAND partition table and index

2013-05-21T09:54:21+00:00

Add NAND partition table, EK board support boot up NAND flash using
the same NAND partition table

Add Index in this file

Signed-off-by: Bo Shen 
Signed-off-by: Andreas Bießmann

ARM: at91: add at91sam9x5 and sama5d3x information

2013-05-21T09:54:20+00:00

This patch add following EK information
  - at91sam9n12ek, at91sam9x5ek
  - sama5d3xek

Signed-off-by: Bo Shen 
Signed-off-by: Andreas Bießmann

ARM: at91: fix and update README.at91 document

2013-05-21T09:54:19+00:00

This patch implement following things
  - The link no longer accessable
  - Remove the error configuration command
  - Update soldered data flash memory map
  - Update at91sam9m10g45ek memory size to 128MiB

Signed-off-by: Bo Shen 
Signed-off-by: Andreas Bießmann

doc: Fix some typos in different files

2012-03-27T11:31:37+00:00

adresses/addresses
alernate/alternate
asssuming/assuming
calcualted/calculated
enviroment/environment
evalutation/evaluation
falsh/flash
labled/labeled
paramaters/parameters

Signed-off-by: Thomas Weber 
Acked-by: Anatolij Gustschin

at91: Introduction of at91sam9g10 SOC.

2009-07-12T15:56:11+00:00

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Signed-off-by: Sedji Gaouaou

at91: Introduction of at91sam9g45 SOC.

2009-07-12T15:43:34+00:00

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou

at91sam9263ek: add nor flash support

2009-06-21T14:18:11+00:00

this will allow you to store use it for the env and to boot directly U-Boot from

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

at91sam9: add watchdog support

2009-04-04T18:42:19+00:00

Signed-off-by: Nicolas Ferre 
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

2009-03-22T13:48:16+00:00

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters 
Signed-off-by: Nicolas Ferre 
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

at91: add at91sam9xeek board support

2009-01-06T20:37:19+00:00

At91sam9xe is basically an at91sam9260 with embedded flash. We can manage
it as another entry for at91sam9260 in the Makefile.

Check documentation at :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4263

Signed-off-by: Nicolas Ferre 
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD