u-boot.git/doc/README.uniphier, branch v2016.09

ARM: uniphier: switch to raw U-Boot image

2016-03-23T16:45:41Z

Now everything is done to load a raw U-Boot proper image instead of an mkimage-processed one (as far as I tested on NAND, eMMC, NOR). The SPL already knows the load address of the U-Boot proper without parsing its uImage header because the load address is defined by CONFIG_SYS_TEXT_BASE, assuming that the two images are generated from the same build. My main motivation of this switch is to use u-boot-with-spl.bin, a concatenation of u-boot-spl.bin and u-boot.bin. (I wish there were a concatenation of u-boot-spl.bin and u-boot.img...) Anyway, this commit would be useful for one-shot image burn. Signed-off-by: Masahiro Yamada

ARM: uniphier: fix README instruction for updating U-Boot via TFTP

2016-03-23T16:45:41Z

Commit 3cb9abc9c512 ("ARM: uniphier: update U-Boot file names in workflow") missed to update these two sentences. Fix them now. Replace u-boot-spl-dtb.bin and u-boot-dtb.img with u-boot-spl.bin and u-boot.img, respectively. Signed-off-by: Masahiro Yamada

ARM: uniphier: document how-to-build for Ace and Sanji boards

2016-03-08T16:10:30Z

Signed-off-by: Masahiro Yamada

ARM: uniphier: merge two defconfig files

2016-02-28T18:50:16Z

PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one image and there is bit more room in SPL to accommodate all of them. Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig. Signed-off-by: Masahiro Yamada

ARM: uniphier: add emmcupdate command

2016-02-28T18:50:16Z

The Boot ROM expects the boot image (SPL) in the Boot Partition 1. So, updating images involves the hardware partition switch. It might be a bit advanced for some users. To be user-friendly, this commit adds a useful command to update the images; just put SPL and U-Boot proper into the public directory of the TFTP server and execute "run emmcupdate" from the command line. Signed-off-by: Masahiro Yamada

mmc: uniphier: add driver for UniPhier SD/MMC host controller

2016-02-28T18:50:15Z

Add a driver for the on-chip SD/eMMC host controller used by UniPhier SoC family. Signed-off-by: Masahiro Yamada

gpio: uniphier: add driver for UniPhier GPIO controller

2016-02-28T18:50:15Z

This GPIO controller device is used on UniPhier SoCs. Signed-off-by: Masahiro Yamada Acked-by: Simon Glass

ARM: uniphier: update U-Boot file names in workflow

2016-02-14T07:36:13Z

Since commit ad1ecd2063da ("fdt: Build a U-Boot binary without device tree") and commit 03c25bcd263a ("fdt: Build an SPL binary without device tree"), we can use shorter file names for the output images. The default configuration for UniPhier SoCs enables CONFIG_OF_SEPARATE and CONFIG_SPL_OF_CONTROL. In this case, spl/u-boot-spl.bin is the same as spl/u-boot-spl-dtb.bin. Likewise, u-boot.img is the same as as u-boot-dtb.img. So, this change of the flow has no impact. Signed-off-by: Masahiro Yamada Reviewed-by: Simon Glass

ARM: uniphier: fix recommended board setting in document

2016-01-12T16:55:02Z

The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c writes/reads the tail of each NOR flash bank to check if the device really resides there. If CS1_SPLIT were enabled, the support card would always require two NOR flash devices to be inserted for the correct NOR detection. This is not probably what we want. Signed-off-by: Masahiro Yamada

ARM: uniphier: rename rest of defconfig files

2015-12-22T15:08:58Z

Rename rest of defconfig files of UniPhier SoC family to have the prefix uniphier_. Signed-off-by: Masahiro Yamada