u-boot.git/doc/board/phytec, branch v2025.04

doc: phytec: imx8mm: add OP-TEE documentation

2025-01-16T13:16:02Z

Add instructions on how to build and package OP-TEE for the phycore-imx8mm based boards. The build instructions are identical for phyGATE-Tauri-L and phyBOARD-Polis. Also fix missig '-' for TF-A build instructions. Signed-off-by: Yannic Moog

doc: phytec: imx8mp: add OP-TEE documentation

2025-01-16T13:16:02Z

Add documentation for the phyBOARD-Pollux i.MX 8M Plus on OP-TEE integration. Also add missing '-' to TF-A build instruction while at it. Signed-off-by: Yannic Moog

Merge patch series "Add phyCORE AM62Ax"

2024-12-14T02:09:41Z

Garrett Giordano says: This patch set adds the phyCORE AM62Ax board support and documenation to u-boot. The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can be used in combination with different carrier boards. This module can come with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs from the AM62x family. A development Kit, called phyBOARD-Lyra is used as a carrier board reference design around the AM62x SoM. This series depends on the following two patches: - [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL https://lists.denx.de/pipermail/u-boot/2024-October/570156.html - [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH https://lists.denx.de/pipermail/u-boot/2024-November/571543.html Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com [trini: Fix warning in board/phytec/common/k3/board.c when CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled] Signed-off-by: Tom Rini

doc: board: phytec: Add phyCORE-AM62ax

2024-12-13T23:30:01Z

Add documentation for PHYTEC phyCORE-AM62ax SoM. Signed-off-by: Garrett Giordano Reviewed-by: Wadim Egorov Reviewed-by: Dhruva Gole

board: phytec: imx93: Add phyCORE-i.MX 93 support for all SOM variants

2024-11-26T02:08:02Z

The phyCORE-i.MX 93 is available in various variants (e.g. different ram sizes, eMMC HS400 yes/no). Enable hardware introspection for the imx93-phyboard-segin_defconfig, so that during startup the SOM module variant can be detected, and the hardware can be configured accordingly. The resulting SPL and u-boot binary shall able to boot each phyCORE-i.MX 93 module variant on each carrier board. Finally rename imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight its SOM scope. Signed-off-by: Christoph Stoidner Reviewed-by: Wadim Egorov Reviewed-by: Yannic Moog

arm: dts: phycore-am62x: Package TIFS Stub

2024-08-09T00:37:09Z

Add support for packaging the TIFS Stub as it's required for basic Low Power Modes like Deep Sleep. The reason it is packaged using binman and not inherently as part of the DM firmware is because for HS devices, customer owns the customer key and only customer has access to it. DM is release by TI, Since TI doesn't have access to the customer key it cannot have a component that is signed by customer key. Hence, it's left as part of binman to be signed and packaged. While at it, also make sure it's documented in phycore-am62x Reviewed-by: Nishanth Menon Reviewed-by: Wadim Egorov Signed-off-by: Dhruva Gole

doc: board: ti: Update to use the new boot firmware labels

2024-08-09T00:37:08Z

Use the new boot_firmwares labels that help make documentation more specific as to which firmwares are used in which devices Signed-off-by: Dhruva Gole

doc: board: phytec: phycore-am6: Describe UART based boot

2024-07-05T19:57:01Z

Describe how to boot via UART. Signed-off-by: Wadim Egorov

Merge tag 'v2024.07-rc5' into next

2024-06-24T19:34:52Z

Prepare v2024.07-rc5

doc: board: phytec: phycore-am6: Use mtd commands

2024-06-18T16:29:00Z

Update Flash to SPI NOR chapter for use with mtd commands. This is more convenient as we do not have to remember any offsets in the SPI. Signed-off-by: Wadim Egorov Reviewed-by: Daniel Schultz