The LVDS Display Interface Transmitter handles the LVDS protocol:
it maps the pixels received from the upstream Pixel-DMA (LTDC)
onto the LVDS PHY.

The LVDS controller driver supports the following high-level features:
        • FDP-Link-I and OpenLDI (v0.95) protocols
        • Single-Link or Dual-Link operation
        • Single-Display or Double-Display (with the same content
          duplicated on both)
        • Flexible Bit-Mapping, including JEIDA and VESA
        • RGB888 or RGB666 output
        • Synchronous design, with one input pixel per clock cycle
        • No resolution limitation.

Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>

Clarify the usage of SCMI specific device tree to use with
stm32mp15_defconfig and with OP-TEE.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Title underlines should match the length of the title. Unfortunately
docutils only catches underlines that are too short.

Add some missing empty lines after titles.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Use proper project name in comments, Kconfig, readmes.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/0dbdf0432405c1c38ffca55703b6737a48219e79.1684307818.git.michal.simek@amd.com

Use internal rst reference with :doc: to have a link to distro.rst page
in the generated U-Boot documentation.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Commit 37c5195dfcd157 ("doc: Move distro boot doc to rST") renamed
doc/README.distro to doc/develop/distro.rst.

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

When OP-TEE is used, the SMC for BSEC management are not available and
the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13
and it is a new feature for STM32MP15x).

The BSEC driver try to open a session to this PTA BSEC at probe
and use it for OTP read or write access to fuse or to shadow.

This patch also adapts the commands stm32key and stboard to handle
the BSEC_LOCK_PERM lock value instead of 1.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.

Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1

The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.

These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Add in U-Boot documentation the quick instruction to
setup the STMicroelectronics STM32MP13x boards.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Update author email address with the one dedicated to
upstream activities.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>