Use upstream device tree files and bindings. To do so: - imply (enable) OF_UPSTREAM option for E850-96 target - point DEFAULT_DEVICE_TREE in E850-96 config to upstream dts - remove now not needed local dts files, binding docs and headers - update MAINTAINERS and board/samsung/e850-96/MAINTAINERS correspondingly Upstream device tree files for Exynos850 SoC and E850-96 board are pretty much the same as local (removed) ones, so the conversion is rather straightforward and painless in this case. The appended dts file (arch/arm/dts/exynos850-e850-96-u-boot.dtsi) stays unchanged. The only remaining local dt-bindings doc for E850-96 board is exynos-pmu.yaml. It wasn't removed as it's quite different from Linux kernel version. Particularly U-Boot local version of exynos-pmu.yaml describes "samsung,uart-debug-1" property, which is not present in Linux kernel binding. Later it might be upstreamed to Linux kernel, and once it's done the U-Boot exynos-pmu.yaml binding can be removed. No functional change. Acked-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Remove redundant device tree files now that RK3399 boards have been migrated to use OF_UPSTREAM. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bindings documentation and the header file for Exynos850 clock controller. It was taken from Linux kernel [1,2]. [1] Documentation/devicetree/bindings/clock/samsung,exynos850-clock.yaml [2] include/dt-bindings/clock/exynos850.h Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replace instances of http://www.ti.com with https://www.ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
Now that Linux has accepted these tags, move U-Boot over to use them. Signed-off-by: Simon Glass <sjg@chromium.org>
With device tree binding migration to yaml it is difficult to synchronize the binding from Linux kernel to U-Boot. Instead of maintaining the same dt bindings, this patch adds in the U-Boot documentation the path to the device tree bindings in Linux kernel for STMicroelectronics devices, when they are used without modification. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Add links for referenced text files. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The PLL1 node (st,pll1) is optional in device tree, the max supported frequency define in OPP node is used when the node is absent. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix the following DT dtc warnings for stm32mp1 boards: Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0: node has a unit name, but no reg property Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1: node has a unit name, but no reg property Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2: node has a unit name, but no reg property Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3: node has a unit name, but no reg property Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for CDCE913/925/937/949 family of devices. These are modular PLL-based low cost, high performance, programmable clock synthesizers, multipliers and dividers. They generate up to 9 output clocks from a single input frequency. The initial version of the driver does not support programming of the PLLs, and thus they run in the bypass mode only. The code is loosely based on the linux kernel cdce9xx driver. Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add precision for disabled fixed clock in stm32mp1 binding. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>