Some I2C slave devices are read-only and don't even answer with NACK.
For example FD65x segment LED controllers.
Make them usable with i2c-gpio,sda-output-only that are already supported
by Linux 6.3+.

Signed-off-by: Alex Shumsky <alexthreed@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

Add description for fifo-depth parameter that can be used
in the device tree.

Signed-off-by: Pei Yue Ho <peiyue.ho@starfivetech.com>
Reviewed-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Reviewed-by: Eng Lee Teh <englee.teh@starfivetech.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

With device tree binding migration to yaml it is difficult to synchronize
the binding from Linux kernel to U-Boot.

Instead of maintaining the same dt bindings, this patch adds in the U-Boot
documentation the path to the device tree bindings in Linux kernel for
STMicroelectronics devices, when they are used without modification.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>

Add links for referenced text files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.

This can be handled by a generic driver along with some information in the
device tree.

Add a generic i2c driver for this purpose.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- i2c/nx_i2c.c: Some adaptions mainly because of changes in
  "struct udevice".
- several Bugfixes in nx_i2c.c.
- the driver has been for s5p6818 only. Code extended appropriately
  in order s5p4418 is also working.
- "probe_chip" added.
- pinctrl-driver/dt is used instead of configuring the i2c I/O-pins
  in the i2c-driver.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
  possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).

Signed-off-by: Stefan Bosch <stefan_b@posteo.net>

Add I2C controller support for Cortina Access CAxxxx SoCs

Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

hs: fixed build error, add include log.h

Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>

This adds support for clock stretching to the i2c-gpio driver. This is
accomplished by switching the GPIO used for the SCL line to an input
when it should be driven high, and polling on the SCL line value until
it goes high (indicating that the I2C slave is no longer pulling it
low).

This is enabled by default; for gpios which cannot be configured as
inputs, the i2c-gpio,scl-output-only property can be used to fall back
to the previous behavior.

Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

Document the gpio-i2c deblocking sequence binding.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

Bring in this file from Linux v5.4.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>