This adds the necessary dt-bindings and documentation to use the ADI
SC5xx pinctrl driver in a device tree. It is not yet available upstream
in the Linux kernel. Eventually, it will be moved there.

Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>

Most Rockchip device tree related bindings are converted to YAML
and available in the U-boot /dts/upstream/Bindings/ directory.
Remove all redundant U-boot entries.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>

Now that Linux has accepted these tags, move U-Boot over to use them.

Signed-off-by: Simon Glass <sjg@chromium.org>

"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.

Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>

This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

With device tree binding migration to yaml it is difficult to synchronize
the binding from Linux kernel to U-Boot.

Instead of maintaining the same dt bindings, this patch adds in the U-Boot
documentation the path to the device tree bindings in Linux kernel for
STMicroelectronics devices, when they are used without modification.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>

Add links for referenced text files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).

The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"

This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".

Change the "pwmN" groups to support "led" function.

Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Document slew-rate DT binding for SAMA7G5.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Add drive strength property which is equivalent with the one in Linux

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>