u-boot.git/doc/device-tree-bindings, branch v2017.01

regulator: fixed: Add support to handle enable-active-high DT property

2016-12-27T13:22:57+00:00

Add support to handle enable-active-high DT property. This property is
used to drive the gpio controlling fixed regulator as active high when
claiming gpio line.

Signed-off-by: Vignesh R 
Acked-by: Simon Glass

arm64: mvebu: Add pin control nodes to A8K family DTS files

2016-12-12T08:04:52+00:00

Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files

Signed-off-by: Konstantin Porotchkin 
Cc: Stefan Roese 
Cc: Nadav Haklai 
Cc: Neta Zur Hershkovits 
Cc: Omri Itach 
Cc: Igal Liberman 
Cc: Haim Boot 
Cc: Hanna Hawa 
Signed-off-by: Stefan Roese

arm64: mvebu: pinctrl: Add pin control driver for A8K family

2016-12-12T08:04:52+00:00

Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.

Signed-off-by: Konstantin Porotchkin 
Reviewed-by: Simon Glass 
Cc: Simon Glass 
Cc: Stefan Roese 
Cc: Nadav Haklai 
Cc: Neta Zur Hershkovits 
Cc: Omri Itach 
Cc: Igal Liberman 
Cc: Haim Boot 
Cc: Hanna Hawa 
Signed-off-by: Stefan Roese

serial: pl01x: expose skip_init platdata option in DT

2016-11-29T01:09:47+00:00

To be able to represent the skip-init platdata element with OF_CONTROL,
it needs to be read from the device tree as well and put into the platform data.

Cc: Eric Anholt 
Signed-off-by: Fabian Vogt 
Reviewed-by: Simon Glass

serial: bcm283x_mu: add device tree support

2016-11-29T01:09:46+00:00

This patch adds device tree support for the bcm283x mini-uart driver.

Signed-off-by: Fabian Vogt 
Reviewed-by: Simon Glass

gpio: bcm2835: add device tree support

2016-11-29T01:09:45+00:00

This patch adds device tree support for the bcm2835 GPIO driver.

Signed-off-by: Fabian Vogt 
Reviewed-by: Simon Glass

sf: Rename sf_params.c to spi_flash_ids.c

2016-11-18T07:34:54+00:00

Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.

Cc: Bin Meng 
Cc: York Sun 
Cc: Vignesh R 
Cc: Mugunthan V N 
Cc: Michal Simek 
Signed-off-by: Jagan Teki 
Reviewed-by: Jagan Teki 
Tested-by: Jagan Teki 
Reviewed-by: Siva Durga Prasad Paladugu

dt: net: add DWC EQoS binding

2016-11-07T17:28:15+00:00

The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which
supports multiple options for bus type, clocking and reset structure, and
feature list.

This patch imports the binding from the Linux kernel, including my V3
patch to extend the binding to cover the Tegra186, which is applied for
next-20160912. So far, my changes have been acked by Lars Persson, the
original author of the binding.

Signed-off-by: Stephen Warren 
Reviewed-by: Simon Glass 
Acked-by: Joe Hershberger

power: pmic: add Ricoh RN5T567 PMIC support

2016-10-07T10:26:15+00:00

Add device model enabled PMIC driver for Ricoh RN5T567 PMIC used
on Colibri iMX7.

Signed-off-by: Stefan Agner 
Reviewed-by: Simon Glass

dm: imx: serial: support device tree

2016-10-07T10:26:14+00:00

Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.

Signed-off-by: Stefan Agner 
Reviewed-by: Simon Glass