u-boot.git/doc/device-tree-bindings, branch v2019.07-rc2

ARM: socfpga: Description on FPGA bitstream type and file name for Arria 10

2019-05-10T20:48:10Z

This patch adds description on properties about file name used for both peripheral bitstream and core bitstream. Signed-off-by: Tien Fong Chee

net: phy: micrel: Use correct skew values on KSZ9021

2019-05-08T22:27:01Z

Commit ff7bd212cb8a ("net: phy: micrel: fix divisor value for KSZ9031 phy skew") fixed the skew value divisor for the KSZ9031, but left the code using the same divisor for the KSZ9021, which is incorrect. The preceding commit c16e69f702b1 ("net: phy: micrel: add documentation for Micrel KSZ90x1 binding") added the DTS documentation for the KSZ90x1, changing it from the equivalent file in the Linux kernel to correctly state that for this part the skew value is set in 120ps steps, whereas the Linux documentation and driver continue to this day to use the incorrect value of 200 that came from the original KSZ9021 datasheet before it was corrected in revision 1.2 (Feb 2014). This commit sorts out the resulting confusion in a consistent way by making the following changes: - Update the documentation to be clear about what the skew values mean, in the same was as for the KSZ9031. - Update the Micrel PHY driver to select the appropriate divisor for both parts. - Adjust all the device trees that state skew values for KSZ9021 PHYs to use values based on 120ps steps instead of 200ps steps. This will result in the same values being programmed into the skew registers as the equivalent device trees in the Linux kernel do, where it incorrectly uses 200ps steps (since that's where all these device trees were copied from). Signed-off-by: James Byrne Acked-by: Joe Hershberger

led: add initial support for bcm6858

2019-04-22T22:13:24Z

The driver add the support of the led IP on bcm6858. This led IP can drive up to 32 leds, and can handle blinking. Signed-off-by: Philippe Reynes Reviewed-by: Daniel Schwierzeck

stm32mp1: add stusb1600 support for DK1 and DK2 board

2019-04-21T08:26:52Z

The DK1 and DK2 boards use the USB Type-C controller STUSB1600. This patch updates: - the device tree to add the I2C node in the DT - the board stm32mp1 to probe this I2C device and use this controller to check cable detection. - the DWC2 driver to support a new dt property "u-boot,force-b-session-valid" which forces B session and device mode; it is a workaround because the VBUS sensing and ID detection isn't available with stusb1600. Signed-off-by: Patrick Delaunay Reviewed-by: Lukasz Majewski

usb: dwc2: add support for STM32MP1

2019-04-21T08:26:52Z

Add compatible "st,stm32mp1-hsotg" and associated driver data to manage the usb33d-supply and the ST specific register for VBus sensing. Signed-off-by: Patrick Delaunay # Conflicts: # drivers/usb/gadget/dwc2_udc_otg.c Reviewed-by: Lukasz Majewski

usb: dwc2: convert driver to DM_USB_GADGET

2019-04-21T08:26:51Z

Minimal conversion to driver model by using the uclass UCLASS_USB_GADGET_GENERIC based on: - reset uclass - clock uclass - generic uclass. Signed-off-by: Patrick Delaunay Reviewed-by: Lukasz Majewski

phy: usbphyc: Binding update of vdda supply

2019-04-21T08:26:51Z

Move supply vdda1v1 and vdda1v8 in usbphyc node and no more in port Signed-off-by: Patrick Delaunay

ARC: dwmmc: Adding DesignWare MMC driver support for ARC devboards

2019-04-18T06:12:38Z

Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys ARC devboards. It is created to switch ARC devboards to use DM_MMC. It required information such as clocks (Bus Interface Unit clock, Card Interface Unit clock) and SDIO bus width. Signed-off-by: Eugeniy Paltsev Signed-off-by: Alexey Brodkin

Merge branch 'master' of git://git.denx.de/u-boot-spi

2019-04-14T04:03:06Z

Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: Tom Rini

Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-boot

2019-04-12T19:43:19Z

stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver