u-boot.git/doc/device-tree-bindings, branch v2020.01

doc: really get rid of Documentation/ directory

2019-12-13T18:01:53+00:00

Commit 656d8da9d2 (doc: Remove duplicated documentation directory) got
rid of most of Documentation/. But there's still an obviously useless
.gitignore left behind.

Also, there's a copy of the linux kernel's net/ethernet.txt binding
imported from v5.0, while the existing one in doc/ is from 4.0-rc1. So
replace the latter by the former, and making Documentation/ finally
empty.

Signed-off-by: Rasmus Villemoes 
Reviewed-by: Simon Goldschmidt

doc: bindings: Aquantia PHY node binding

2019-12-09T15:47:43+00:00

A couple of optional properties have been introduced for Aquantia PHY
allowing the driver to set up wiring related configuration points that
are otherwise driven by firmware.

Signed-off-by: Alex Marginean 
Acked-by: Joe Hershberger

doc: bindings: add bindings document for PHY nodes

2019-12-09T15:47:43+00:00

It defines that PHY nodes must be children on MDIO bus nodes and defines
the only required property in U-Boot, reg.  This property along with the
example provided are copied over from Linux.

Signed-off-by: Alex Marginean 
Acked-by: Joe Hershberger

dt-bindings: phy: dp83867: Add documentation for disabling clock output

2019-12-09T15:47:42+00:00

Based on commit 980066e6d964 ("dt-bindings: phy: dp83867: Add documentation
for disabling clock output") of mainline linux kernel.

The clock output is generally only used for testing and development and not
used to daisy-chain PHYs.  It's just a source of RF noise afterward.

Add a mux value for "off".  I've added it as another enumeration to the
output property.  In the actual PHY, the mux and the output enable are
independently controllable.  However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.

Document that PHY's default setting will be left as is if the property
is omitted.

Signed-off-by: Grygorii Strashko 
Acked-by: Joe Hershberger

dm: regulator: support regulator more state

2019-11-10T12:31:09+00:00

support parse regulator standard property:
regulator-off-in-suspend;
regulator-init-microvolt;
regulator-suspend-microvolt:
 regulator_get_suspend_enable
 regulator_set_suspend_enable
 regulator_get_suspend_value
 regulator_set_suspend_value

Signed-off-by: Joseph Chen 
Signed-off-by: Elaine Zhang 
Reviewed-by: Kever Yang

dt-bindings: memory-controller: Introduce J721E DDRSS bindings

2019-10-25T21:33:21+00:00

Add DT binding documentation for DDR sub system present on J721E device.

Signed-off-by: Lokesh Vutla

Merge branch '2019-10-11-master-imports'

2019-10-12T14:10:59+00:00

- Assorted cleanups
- FAT bugfixes
- mediatek platform updates

clk: cdce9xx: add support for cdce9xx clock synthesizer

2019-10-11T17:32:39+00:00

Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.

Signed-off-by: Tero Kristo

dt-bindings: phy: add a document for MediaTek tphy

2019-10-11T14:10:18+00:00

This adds a document for tphy which supports physical layer
functionality for a number of controllers on MediaTek SoCs,
such as, USB2.0, USB3.0, PCIe, and SATA.

Signed-off-by: Ryder Lee 
Signed-off-by: Frank Wunderlich

dt-bindings: pcie: add a document for MT7623 PCIe controller

2019-10-11T14:10:18+00:00

This adds a document for MT7623 PCIe controller.

Signed-off-by: Ryder Lee 
Signed-off-by: Frank Wunderlich