u-boot.git/doc, branch v2011.03-rc1

Minor Coding Style Cleanup.

2011-02-02T21:36:10+00:00

Signed-off-by: Wolfgang Denk

OMAP3: add CM-T35 board

2011-02-01T23:54:43+00:00

This patch adds support for CM-T35 board

Signed-off-by: Mike Rapoport 
Signed-off-by: Sandeep Paulraj

Add support for Freescale's mx35pdk board.

2011-02-01T23:54:43+00:00

The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface

Signed-off-by: Stefano Babic

imximage: Add MX53 boot image support

2011-02-01T23:54:42+00:00

This patch add the MX53 boot image support.

This patch has been tested on Freescale MX53EVK board
and MX51EVK board.

Signed-off-by: Jason Liu

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

2011-01-25T20:13:04+00:00

mpc85xx: Enable unique mode registers and dynamic ODT for DDR3

2011-01-20T04:58:23+00:00

Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.

Enable address parity and RCW by default for RDIMMs.

Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.

Use a formula to calculate rodt_on for timing_cfg_5.

Signed-off-by: York Sun 
Signed-off-by: Kumar Gala

mpc8xxx: Enable ECC on/off control in hwconfig

2011-01-20T04:58:23+00:00

Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.

Updated hwconfig calls to use local buffer.

Syntax is
hwconfig=fsl_ddr:ecc=on

Signed-off-by: York Sun 
Signed-off-by: Kumar Gala

Escape minus signs in manpage

2011-01-18T23:07:51+00:00

By default, "-" chars are interpreted as hyphens (U+2010) by groff, not
as minus signs (U+002D). Since options to programs use minus signs
(U+002D), this means for example in UTF-8 locales that you cannot cut
and paste options, nor search for them easily.

(Reported by lintian.)

Signed-off-by: Lo�c Minier

mpc5200, digsy_mtc: add support for rev5 board version

2011-01-18T22:34:26+00:00

difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
  depending on the detected flash size.
- added Werner Pfister 
  as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
  document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
  boards
- change doc/README.cfi as Stefan Roese suggested

Signed-off-by: Heiko Schocher 
Signed-off-by: Stefan Roese 
Acked-by: Detlev Zundel 
cc: Wolfgang Denk 
cc: Stefan Roese 
cc: Werner Pfister 
cc: Detlev Zundel

85xx boards: Rename CONFIG_DDR_DLL to CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN

2011-01-14T07:32:19+00:00

This config option is for an erratum workaround; rename it to be more
clear.  Also, drop it from config files don't need it and were
undefining it.

Signed-off-by: Becky Bruce 
Signed-off-by: Kumar Gala