u-boot.git/doc, branch v2013.07-rc1

Merge branch 'master' of git://git.denx.de/u-boot-arm

2013-06-13T19:16:15Z

Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR Conflicts: arch/arm/include/asm/arch-omap5/omap.h Signed-off-by: Tom Rini

arm: Remove OMAP2420H4 and all omap24xx support

2013-06-10T12:43:19Z

The omap2420H4 was the only mainline omap24xx board. Prior to being fixed by Jon Hunter in time for v2013.04 it had been functionally broken for a very long time. Remove this board as there's not been interest in it in U-Boot for quite a long time. Signed-off-by: Tom Rini

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

2013-06-08T12:35:10Z

Conflicts: drivers/serial/Makefile

Merge branch 'master' of git://git.denx.de/u-boot-video

2013-06-07T12:35:36Z

lcd: add functions to set up simplefb device tree

2013-06-05T20:40:03Z

simple-framebuffer is a new device tree binding that describes a pre- configured frame-buffer memory region and its format. The Linux kernel contains a driver that supports this binding. Implement functions to create a DT node (or fill in an existing node) with parameters that describe the framebuffer format that U-Boot is using. This will be immediately used by the Raspberry Pi board in U-Boot, and likely will be used by the Samsung ARM ChromeBook support soon too. It could well be used by many other boards (e.g. Tegra boards with built-in LCD panels, which aren't yet supported by the Linux kernel). Signed-off-by: Stephen Warren Acked-by: Simon Glass

arm: vf610: Add Vybrid VF610 to mxc_ocotp document

2013-06-03T08:56:54Z

This patch adds Vybrid VF610 to mxc_ocotp document. Signed-off-by: Alison Wang Reviewed-by: Benoît Thébaudeau

arm: vf610: Add Vybrid VF610 CPU support

2013-06-03T08:56:53Z

This patch adds generic codes to support Freescale's Vybrid VF610 CPU. It aligns Vybrid VF610 platform with i.MX platform. As there are some differences between VF610 and i.MX platforms, the specific codes are in the arch/arm/cpu/armv7/vf610 directory. Signed-off-by: Alison Wang Reviewed-by: Benoît Thébaudeau

Merge branch 'u-boot/master' into 'u-boot-arm/master'

2013-05-30T12:45:06Z

Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c

board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32M

2013-05-24T21:54:12Z

Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George Signed-off-by: Andy Fleming

powerpc/t4240qds: Add VDD override

2013-05-24T21:54:10Z

Allow VDD voltage overriding with a command. This is an add-on feasture of VID. To override VDD, use command vdd_override with the value of voltage in mV, for example vdd_override The above example will set the VDD to 1.050 volt. Any wrong value out of range of 0.8188 to 1.2125 volt or invalid string is ignored. In addition to the command, if overriding VDD is needed earlier in booting process, save an variable and reboot: setenv t4240qds_vdd_mv saveenv Signed-off-by: York Sun Signed-off-by: Andy Fleming