u-boot.git/doc, branch v2018.03-rc1

efi_loader: add a README.iscsi describing booting via iSCSI

2018-01-28T20:37:13Z

The appended README explains how U-Boot and iPXE can be used to boot a diskless system from an iSCSI SAN. The maintainer for README.efi and README.iscsi is set. Signed-off-by: Heinrich Schuchardt [agraf: s/Adress/Address/] Signed-off-by: Alexander Graf

Merge git://git.denx.de/u-boot-spi

2018-01-26T12:46:34Z

dts: cadence_spi: Update documentation for DT bindings

2018-01-24T06:37:50Z

Update documentation to reflect adopting the Linux DT bindings. Tested on TI K2G platform: Tested-by: Vignesh R Tested on a socfpga-cyclonev board: Tested-by: Simon Goldschmidt Signed-off-by: Jason Rush Reviewed-by: Jagan Teki Acked-by: Simon Goldschmidt Acked-by: Marek Vasut

fs: Migrate ext4 to Kconfig

2018-01-22T21:43:30Z

Migrate the following symbols to Kconfig: CONFIG_FS_EXT4 CONFIG_EXT4_WRITE The definitions in config_fallbacks.h can now be expressed in Kconfig. Signed-off-by: Tuomas Tynkkynen

m68k: Drop unreferenced CONFIG_* defines

2018-01-19T20:49:32Z

The following config symbols are only defined once and never referenced anywhere else: CONFIG_AMCORE CONFIG_ASTRO5373L CONFIG_M52277EVB CONFIG_M5253DEMO CONFIG_M5253EVBE CONFIG_M5275EVB CONFIG_M54418TWR CONFIG_STMARK2 Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen

ARM: Document AArch64 version of qemu-arm

2018-01-19T20:49:31Z

It's mostly obvious, except that QEMU is annoying and requires an explicit '-cpu cortex-a57' (or some other 64-bit core) to actually run in 64-bit mode. While at it, remove the references to setting the ARCH environment variable; that is not used in U-Boot. Signed-off-by: Tuomas Tynkkynen Reviewed-by: Tom Rini

doc: fix incorrect usage of DT node unit address

2018-01-16T01:29:21Z

The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in various documentation files where this was not observed, to not give bad examples to the reader. Signed-off-by: Andre Przywara

doc: FIT image: fix incorrect examples of DT node unit address

2018-01-16T01:29:21Z

The DT spec demands a unit-address of a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the FIT image example files where this was not observed, to not give bad examples to the reader. Signed-off-by: Andre Przywara

doc: FIT image: fix incorrect description of DT node unit address

2018-01-16T01:29:21Z

The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the FIT image documentation files where this was not observed, to not give bad examples to the reader. Signed-off-by: Andre Przywara

riscv: doc: Add relative doc to describe RISC-V

2018-01-12T13:05:12Z

Add documents to describe NX25 and AE250. Also update other documents for RISC-V. Signed-off-by: Rick Chen Signed-off-by: Rick Chen Signed-off-by: Greentime Hu