Not all Keystone2 devices has AEMIF NAND controller. So adding Kconfig
entry for CONFIG_TI_AEMIF and enabling it in respective defconfigs on
platforms with AEMIF controller.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

Add a uclass that supports Pulse Width Modulation (PWM) devices. It
provides methods to enable/disable and configure the device.

Signed-off-by: Simon Glass <sjg@chromium.org>

This commit adds:
- new uclass id: UCLASS_ADC
- new uclass driver: drivers/adc/adc-uclass.c

The new uclass's API allows for ADC operation on:
* single-channel with channel selection by a number
* multti-channel with channel selection by bit mask

ADC uclass's functions:
* single-channel:
  - adc_start_channel()        - start channel conversion
  - adc_channel_data()         - get conversion data
  - adc_channel_single_shot()  - start/get conversion data
* multi-channel:
  - adc_start_channels()       - start selected channels conversion
  - adc_channels_data()        - get conversion data
  - adc_channels_single_shot() - start/get conversion data for channels
                                 selected by bit mask
* general:
  - adc_stop()      - stop the conversion
  - adc_vdd_value() - positive reference Voltage value with polarity [uV]
  - adc_vss_value() - negative reference Voltage value with polarity [uV]
  - adc_data_mask() - conversion data bit mask

The device tree can provide below constraints/properties:
- vdd-polarity-negative: if true: Vdd = vdd-microvolts * (-1)
- vss-polarity-negative: if true: Vss = vss-microvolts * (-1)
- vdd-supply:            phandle to Vdd regulator's node
- vss-supply:            phandle to Vss regulator's node
And optional, checked only if the above corresponding, doesn't exist:
  - vdd-microvolts:      positive reference Voltage [uV]
  - vss-microvolts:      negative reference Voltage [uV]

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Implement a Timer uclass to work with lib/time.c.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>

Many System on Chip(SoC) solutions are complex with multiple processors
on the same die dedicated to either general purpose of specialized
functions. Many examples do exist in today's SoCs from various vendors.
Typical examples are micro controllers such as an ARM M3/M0 doing a
offload of specific function such as event integration or power
management or controlling camera etc.

Traditionally, the responsibility of loading up such a processor with a
firmware and communication has been with a High Level Operating
System(HLOS) such as Linux. However, there exists classes of products
where Linux would need to expect services from such a processor or the
delay of Linux and operating system being able to load up such a
firmware is unacceptable.

To address these needs, we need some minimal capability to load such a
system and ensure it is started prior to an Operating System(Linux or
any other) is started up.

NOTE: This is NOT meant to be a solve-all solution, instead, it tries to
address certain class of SoCs and products that need such a solution.

A very simple model is introduced here as part of the initial support
that supports microcontrollers with internal memory (no MMU, no
execution from external memory, or specific image format needs). This
basic framework can then (hopefully) be extensible to other complex SoC
processor support as need be.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>

This creates a new framework for handling of pin control devices,
i.e. devices that control different aspects of package pins.

This uclass handles pinmuxing and pin configuration; pinmuxing
controls switching among silicon blocks that share certain physical
pins, pin configuration handles electronic properties such as pin-
biasing, load capacitance etc.

This framework can support the same device tree bindings, but if you
do not need full interface support, you can disable some features to
reduce memory foot print.  Typically around 1.5KB is necessary to
include full-featured uclass support on ARM board (CONFIG_PINCTRL +
CONFIG_PINCTRL_FULL + CONFIG_PINCTRL_GENERIC + CONFIG_PINCTRL_PINMUX),
for example.

We are often limited on code size for SPL.  Besides, we still have
many boards that do not support device tree configuration.  The full
pinctrl, which requires OF_CONTROL, does not make sense for those
boards.  So, this framework also has a Do-It-Yourself (let's say
simple pinctrl) interface.  With CONFIG_PINCTRL_FULL disabled, the
uclass itself provides no systematic mechanism for identifying the
peripheral device, applying pinctrl settings, etc.  They must be
done in each low-level driver.  In return, you can save much memory
footprint and it might be useful especially for SPL.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>

Sort different types of drivers in alphabetical order.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>

Right now PHYS_TO_BUS shows in the Kconfig main menu, move it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>

Make "Generic Driver Options" menu show on the top in the Kconfig.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>