u-boot.git/drivers/Makefile, branch v2017.07

Drop digital thermometer and thermostat (DTT) drivers

2017-05-22T12:37:11+00:00

This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.

Signed-off-by: Simon Glass 
Reviewed-by: Heiko Schocher 
Reviewed-by: Tom Rini

Drop three-wire serial (TWS) support

2017-05-22T12:37:10+00:00

This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.

Also drop the rtc4543 RTC driver since it uses TWS.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini

mmc: descend into drivers/mmc only when CONFIG_MMC is enabled

2017-05-15T09:28:23+00:00

This simplifies makefiles.  Also, arrange the order of objects in
drivers/mmc/Makefile so that the framework objects are listed before
drivers.

Signed-off-by: Masahiro Yamada

drivers: phy: add generic PHY framework

2017-05-09T18:14:16+00:00

The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.

Signed-off-by: Jean-Jacques Hiblot 
Reviewed-by: Simon Glass

sysreset: psci: support system reset in a generic way with PSCI

2017-04-18T14:29:19+00:00

If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.

The arm-smccc is supported on ARMv7 or later.  Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31.  In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.

Signed-off-by: Masahiro Yamada

dm: core: Allow driver model to be disabled for TPL

2017-04-05T20:36:58+00:00

Since TPL often needs to be very very small it may not make sense to
enable driver model. Add an option for this.

This changes brings the 'rock' board under the TPL limit with gcc 4.9.

Signed-off-by: Simon Glass

spl: Allow PCH drivers to be used in SPL

2017-02-06T03:38:46+00:00

Add an option for building Platorm Controller Hub drivers in SPL.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

spl: Allow timer drivers to be used in SPL

2017-02-06T03:38:46+00:00

Add a new Kconfig option to allow timer drivers to be used in SPL.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

spl: Allow RTC drivers to be used in SPL

2017-02-06T03:38:46+00:00

Add a new Kconfig option to allow RTC drivers to be used in SPL.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

spl: Allow PCI drivers to be used in SPL

2017-02-06T03:38:46+00:00

Add a new Kconfig option to allow PCI drivers to be used in SPL.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng