u-boot.git/drivers/Makefile, branch v2017.09-rc1

drivers: Enable FPGA driver build on SPL

2017-07-26T08:31:44Z

Enable FPGA driver build for Arria 10 SPL because FPGA driver is needed by Arria 10 SPL to configure and getting DDR up before loading U-boot into DDR and booting from there. Signed-off-by: Tien Fong Chee Reviewed-by: Ley Foon Tan Reviewed-by: Dinh Nguyen

scsi: Move drivers into new drivers/scsi directory

2017-07-11T16:08:19Z

At present we have the SCSI drivers in the drivers/block and common/ directories. It is better to split them out into their own place. Use drivers/scsi which is what Linux does. Signed-off-by: Simon Glass Reviewed-by: Bin Meng

sata: Move drivers into new drivers/ata directory

2017-07-11T16:08:19Z

At present we have the SATA and PATA drivers mixed up in the drivers/block directory. It is better to split them out into their own place. Use drivers/ata which is what Linux does. Signed-off-by: Simon Glass Reviewed-by: Bin Meng

Drop digital thermometer and thermostat (DTT) drivers

2017-05-22T12:37:11Z

This subsystem is quite old. It has been replaced with a driver-model version (UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher Reviewed-by: Tom Rini

Drop three-wire serial (TWS) support

2017-05-22T12:37:10Z

This subsystem has not been converted to driver model, there is only one driver and only one board that uses it. Drop it and its CONFIG option. Also drop the rtc4543 RTC driver since it uses TWS. Signed-off-by: Simon Glass Reviewed-by: Tom Rini

mmc: descend into drivers/mmc only when CONFIG_MMC is enabled

2017-05-15T09:28:23Z

This simplifies makefiles. Also, arrange the order of objects in drivers/mmc/Makefile so that the framework objects are listed before drivers. Signed-off-by: Masahiro Yamada

drivers: phy: add generic PHY framework

2017-05-09T18:14:16Z

The PHY framework provides a set of APIs to control a PHY. This API is derived from the linux version of the generic PHY framework. Currently the API supports init(), deinit(), power_on, power_off() and reset(). The framework provides a way to get a reference to a phy from the device-tree. Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Simon Glass

sysreset: psci: support system reset in a generic way with PSCI

2017-04-18T14:29:19Z

If the system is running PSCI firmware, the System Reset function (func ID: 0x80000009) is supposed to be handled by PSCI, that is, the SoC/board specific reset implementation should be moved to PSCI. U-Boot should call the PSCI service according to the arm-smccc manner. The arm-smccc is supported on ARMv7 or later. Especially, ARMv8 generation SoCs are likely to run ARM Trusted Firmware BL31. In this case, U-Boot is a non-secure world boot loader, so it should not be able to reset the system directly. Signed-off-by: Masahiro Yamada

dm: core: Allow driver model to be disabled for TPL

2017-04-05T20:36:58Z

Since TPL often needs to be very very small it may not make sense to enable driver model. Add an option for this. This changes brings the 'rock' board under the TPL limit with gcc 4.9. Signed-off-by: Simon Glass

spl: Allow PCH drivers to be used in SPL

2017-02-06T03:38:46Z

Add an option for building Platorm Controller Hub drivers in SPL. Signed-off-by: Simon Glass Reviewed-by: Bin Meng