Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.

This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

NVM Express (NVMe) is a register level interface that allows host
software to communicate with a non-volatile memory subsystem. This
interface is optimized for enterprise and client solid state drives,
typically attached to the PCI express interface.

This adds a U-Boot driver support of devices that follow the NVMe
standard [1] and supports basic read/write operations.

Tested with a 400GB Intel SSD 750 series NVMe card with controller
id 8086:0953.

[1] http://www.nvmexpress.org/resources/specifications/

Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
  decision for each stage and under control of $(SPL_TPL_)TIMER
  instead of having the two-level configuration with TIMER and
  $(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
  not be compiled in

This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

To simplify drivers/Makefile a bit when using TPL/SPL, we consistently
use the $(SPL_TPL_) macro to test for drivers that have separate
configuration symbols for the full U-boot, SPL and TPL stages.
Instead of explicitly repeating them in two separate if-guarded
sections of the Makefile, we can now simply list these options once.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Enable FPGA driver build for Arria 10 SPL because FPGA driver is
needed by Arria 10 SPL to configure and getting DDR up before
loading U-boot into DDR and booting from there.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>

At present we have the SCSI drivers in the drivers/block and common/
directories. It is better to split them out into their own place. Use
drivers/scsi which is what Linux does.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

At present we have the SATA and PATA drivers mixed up in the drivers/block
directory. It is better to split them out into their own place. Use
drivers/ata which is what Linux does.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>