u-boot.git/drivers/ata, branch v2020.01-rc2

ata: ahci allow 64-bit DMA for SATA

2019-10-31T11:22:53Z

Allow 64-bit DMA on AHCI. If not supported by the host controller, at least print a message and fail. Signed-off-by: Roman Kapl

ata: ahci: Don't forget to clear upper address regs.

2019-10-11T14:10:19Z

In 32bits mode upper bits need to be set to 0, otherwise controller will try to DMA into not existing memory and stops with error. Tested-by: Frank Wunderlich Signed-off-by: Frank Wunderlich Signed-off-by: Oleksandr Rybalko

ahci-pci: ASM1061 report wrong class, but support AHCI.

2019-10-11T14:10:18Z

Tested-by: Frank Wunderlich Signed-off-by: Frank Wunderlich Signed-off-by: Oleksandr Rybalko

dm: scsi: Scan the actual number of ports

2019-08-26T15:46:20Z

The scsi_scan_dev() is looping over the number of uc_plat->max_id. The number of actual ports a AHCI controller has can be greater than max_id. Update uc_plat->max_id to make SCSI scan all detected ports. Signed-off-by: Aiden Park Reviewed-by: Bin Meng

ata: fsl_ahci: Add sata DM support for Freescale powerpc socs

2019-05-23T14:23:09Z

This patch is to support Freescale sata driver with dts initialized. Also resolved the following problems. ===================== WARNING ====================== This board does not use CONFIG_DM_SCSI. Please update the storage controller to use CONFIG_DM_SCSI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== Signed-off-by: Peng Ma Reviewed-by: Prabhakar Kushwaha

scsi: ceva: Clean up the driver code

2019-05-22T06:54:24Z

Distinguish the ecc val by chassis version and move the ecc addr to dts. Add ls1028a soc support. Signed-off-by: Peng Ma Reviewed-by: Michal Simek Reviewed-by: Prabhakar Kushwaha

ata: ahci: drop read-only ahci_ioports members

2019-05-18T16:32:01Z

Also get rid of ahci_setup_port(..). Signed-off-by: Christian Gmeiner

ata: ahci: fix memory leak

2019-05-09T23:52:55Z

malloc(..) and memalign(..) are both allocating memory and as a result we leak the memory allocated with malloc(..). Signed-off-by: Christian Gmeiner Reviewed-by: Simon Glass

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

2019-04-17T13:19:45Z

- Convert DM_MMC and DM_SCSI - A20, R40, H6 Linux dts(i) sync - CLK, RESET support for sunxi, sun8_emac net drivers

sunxi: update SATA driver to always use DM_SCSI

2019-04-17T09:04:45Z

It seems like the Allwinner SATA driver is already quite capable of using the driver model, so we can force this on all boards and can remove support for a non-DM_SCSI build. This removes the warning about boards with SATA ports not being DM_SCSI compliant. It also takes the opportunity to move the driver out of the board/sunxi directory to join its siblings in drivers/ata, and to make it a proper Kconfig citizen. The board defconfigs stay untouched. Signed-off-by: Andre Przywara Reviewed-by: Simon Glass Reviewed-by: Jagan Teki [jagan: select DM_SCSI separately] Signed-off-by: Jagan Teki