The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)

This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access

Signed-off-by: Roger Quadros <rogerq@ti.com>

This would be useful to start moving various config options.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

Define the new common function sata_port_status() which can be
used to query the sata driver for the state of ports, and implement it
for dwc_ahsata.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>

This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.

The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.

The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port.  This is added under a
suitable ifdef.

This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

In 73545f75b66d "ahci: wait longer for link" I increased the
timeout to 40ms based on the observed behaviour of a WD disk on a
Cubietruck. Since then Karsten Merker and myself have both
observed timeouts with HGST disks (Karsten on Cubietruck, me on
Cubieboard2). Increasing the timeout to ~175ms fixes this, so go
to 200ms for a bit of headroom.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>

The IMX6QUAD/DUAL have SATA, but the IMX6SOLO/DL do not. Return failure
instead of attempting a memory access that results in a data abort and reset.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Commit 2faf5fb82ed6 introduced a regression that causes a data
abort when running scsi init followed by scsi reset.

There are 2 problems with the original commit
1) ALLOC_CACHE_ALIGN_BUFFER() allocates memory on the stack but is
assigned to ataid[port] and used by other functions.
2) The function ata_scsiop_inquiry() tries to free memory which was
never allocated on the heap.

Fix these problems by using tmpid as a temporary cache aligned buffer.
Allocate memory separately for ataid[port] and re-use it if required.

Fixes: 2faf5fb82ed6 (ahci: Fix cache align error messages)

Reported-by: Eli Nidam <elini@marvell.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>

I have observed timeouts on a cubietruck.

The increase to 40ms is completely arbitrary and Works For Me(tm). I
couldn't find a good reference for how long you are supposed to wait,
although googling around it seems like tens of ms rather than single
digits is more common. I don't think there is any harm in waiting a bit
longer.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>

This allow the platform to register the platform ahci device.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>

With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>