u-boot.git/drivers/bootcount/Makefile, branch v2018.03

Migrate generic bootcount to Kconfig

2018-02-24T13:43:42+00:00

Make generate boot counter selected in the same way as other boot count
drivers

Reviewed-by: Lukasz Majewski 
Signed-off-by: Alex Kiernan

Integrate AT91 bootcount driver

2018-02-24T13:43:42+00:00

Integrate Boot counter for Atmel AT91SAM9XE into Kconfig

Reviewed-by: Lukasz Majewski 
Signed-off-by: Alex Kiernan

Convert CONFIG_BOOTCOUNT_AM33XX to Kconfig

2018-02-24T13:43:31+00:00

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_AM33XX

Reviewed-by: Lukasz Majewski 
Reviewed-by: Hannes Schmelzer 
Acked-by: Hannes Schmelzer 
Signed-off-by: Alex Kiernan

bootcount: add support for bootcounter on EXT filesystem

2017-11-20T08:58:31+00:00

Add support for bootcounter on an EXT filesystem.
Sync configuration whitelist.

Signed-off-by: Ian Ray 
Signed-off-by: Martyn Welch

Blackfin: Remove

2017-04-05T17:52:01+00:00

The architecture is currently unmaintained, remove.

Cc: Benjamin Matthews 
Cc: Chong Huang 
Cc: Dimitar Penev 
Cc: Haitao Zhang 
Cc: I-SYST Micromodule 
Cc: M.Hasewinkel (MHA) 
Cc: Marek Vasut 
Cc: Martin Strubel 
Cc: Peter Meerwald 
Cc: Sonic Zhang 
Cc: Valentin Yakovenkov 
Cc: Wojtek Skulski 
Cc: Wojtek Skulski 
Signed-off-by: Tom Rini

i2c, bootcount: add support for bootcounter on i2c devices

2014-02-20T05:46:56+00:00

add support for bootcounter on an i2c device. And add a
README for all bootcounter options.

Signed-off-by: Heiko Schocher

am33xx: Make SoC bootcount driver have its own symbol

2013-11-11T17:17:35+00:00

Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility.  So add
another symbol for the bootcount driver for the IP block.

Acked-by: Heiko Schocher 
Signed-off-by: Tom Rini

bootcount: store bootcount var in environment

2013-11-11T17:16:28+00:00

If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is introduced. If "upgrade_available" is
0, "bootcount" is always 0 therefore no need to save the
environment on u-boot boot, if "upgrade_available" is 1 "bootcount"
is incremented in the environment and environment gets written
on u-boot start.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0 (for example with fw_setenv),
if a boot was successfully.

Signed-off-by: Heiko Schocher

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47+00:00

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h

TI:am33xx: Add bootcount support to ti_am335x_common.h

2013-11-01T19:30:32+00:00

Enable the bootcount driver for am335x in general.  We leave adding a
bootlimit and altbootcmd to the environment to the board ports.

Signed-off-by: Tom Rini