u-boot.git/drivers/bootcount, branch v2015.07

qe: move immap_qe.h from arch directory into common directory

2014-07-22T23:25:54+00:00

ls1021 is arm-core and supports qe too.
Move immap_qe.h into common directory for both arm and powerpc.

Signed-off-by: Zhao Qiang 
Reviewed-by: York Sun

i2c, bootcount: add support for bootcounter on i2c devices

2014-02-20T05:46:56+00:00

add support for bootcounter on an i2c device. And add a
README for all bootcounter options.

Signed-off-by: Heiko Schocher

am33xx: Make SoC bootcount driver have its own symbol

2013-11-11T17:17:35+00:00

Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility.  So add
another symbol for the bootcount driver for the IP block.

Acked-by: Heiko Schocher 
Signed-off-by: Tom Rini

bootcount: store bootcount var in environment

2013-11-11T17:16:28+00:00

If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is introduced. If "upgrade_available" is
0, "bootcount" is always 0 therefore no need to save the
environment on u-boot boot, if "upgrade_available" is 1 "bootcount"
is incremented in the environment and environment gets written
on u-boot start.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0 (for example with fw_setenv),
if a boot was successfully.

Signed-off-by: Heiko Schocher

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47+00:00

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h

TI:am33xx: Add bootcount support to ti_am335x_common.h

2013-11-01T19:30:32+00:00

Enable the bootcount driver for am335x in general.  We leave adding a
bootlimit and altbootcmd to the environment to the board ports.

Signed-off-by: Tom Rini

bootcount_davinci: Switch to scratch register #2

2013-11-01T19:30:22+00:00

The RTC IP block here provides 3 scratch registers.  Currently when
using DeepSleep on am335x the scratch0/1 registers are used so moving
ourself to scratch2 makes cooperation easier.

Signed-off-by: Tom Rini

am33xx, davinci: Create and use

2013-11-01T19:30:22+00:00

Create a common header file for the RTC IP block that is shared between
davinci and am33xx.

Signed-off-by: Tom Rini

drivers: convert makefiles to Kbuild style

2013-10-31T17:26:01+00:00

Signed-off-by: Masahiro Yamada

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38+00:00

Signed-off-by: Wolfgang Denk 
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini