Currently in j721e_init.c we check which firewalls to remove using
the board configuration (e.g CONFIG_TARGET_J721E_R5_EVM). We do this
as J721e and J7200 have different IP and firewalls but use the same
SoC definition (SOC_K3_J721E) even though they are different SoCs.

The idea was they would be similar enough that they both could use
the same SoC config to help with common code sharing. Board checks
would then be used differentiate.

This has grown far too messy to maintain any more, especially now
that there is more than one board using J721e (EVM, SK, Beagle AI64).
As differentiation is done based on board, every one of these boards
would have to have checks added for them. Instead let's split J7200
support out from J721e like how normal new SoC support is done.

This patch touches several subsystems and could not be split much better
as when we add SOC_K3_J7200 we want to make use of it in all spots that
once used the combined SOC_K3_J721E so we can turn off SOC_K3_J721E when
building for J7200 boards.

Signed-off-by: Andrew Davis <afd@ti.com>

Add PSIL data for the AM62P and the J722S SoC family. The PSIL mapping
for the J722S is the same except for the extra instances of the CSI-RX.
So let's reuse the same file for both the AM62P and J722S.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
[bb@ti.com: rebased to U-Boot v2024.01]
Signed-off-by: Bryan Brattlof <bb@ti.com>

Add support for DMA in J784S4 SoC.

Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK

In preparation for enabling ethernet for the am62ax family of SoCs,
introduce the initial DMA channel settings for the am62ax

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[bb@ti.com: expanded on commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.

Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Add PSIL data for AM62x SoC.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add support for DMA in J721S2 SoC.

Signed-off-by: David Huang <d-huang@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add AM64 SoC specific channel mapping and endpoint data.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Much of PSIL endpoint configuration for a given SoC can be known at
compile time, therefore pass them for platform specific data instead of
DT.

Add per SoC's specific PSIL endpoint data. This is to bring driver in
sync with upstream DT.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>

The UDMA-P is intended to perform similar (but significantly upgraded) functions
as the packet-oriented DMA used on previous SoC devices. The UDMA-P module
supports the transmission and reception of various packet types.
The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
channels. Channels in the UDMA-P can be configured to be either Packet-Based or
Third-Party channels on a channel by channel basis.

The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet mode)
- MEM_TO_DEV (Packet mode)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>