Drop all duplicate newlines. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Prepare v2024.07-rc3

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Buffers must not have an unclean cache before being used for DMA - a
pending write-back may corrupt the next dev-to-mem transfer otherwise.

This was consistently noticeable during long TFTP transfers, when an ARP
request is answered by U-Boot in the middle of the transfer:

As U-Boot's arp_receive() reuses the receive buffer to prepare its
reply packet, the beginning of one of the next incoming TFTP packets
is overwritten by the ARP reply. The corrupted packet is ignored, but
the TFTP transfer stalls for a few seconds until a timeout is detected
and a retransmit is triggered.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>

net.h is needed for PKTBUFSRX. Without this definition, the driver will
always use 4 RX buffers, causing am65-cpsw-nuss initialization to fail
when a higher number of buffers is requested.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>

Remove <common.h> from this driver directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

Add PSIL data for the AM62P and the J722S SoC family. The PSIL mapping
for the J722S is the same except for the extra instances of the CSI-RX.
So let's reuse the same file for both the AM62P and J722S.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
[bb@ti.com: rebased to U-Boot v2024.01]
Signed-off-by: Bryan Brattlof <bb@ti.com>

ring_idx was not correctly assigned in case of tflow_id is zero.
Which leads to wrong pairing of DMA for drivers like OSPI.

Fixes: 4312a1dfca26 ("dma: ti: k3-udma: Use ring_idx to pair k3 nav rings")
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>

In udma_probe() the return value of setup_resources() is stored in the
u32 "ch_count" member of "struct udma_dev", due to which any negative
return value which indicates an error is masked.

Fix this by storing the return value of setup_resources() in the already
declared integer variable "ret", followed by assigning it to the "ch_count"
member of "struct udma_dev" in case of no error.

While at it, change the "return ret" at the end of udma_probe() to a
"return 0", to explicitly indicate that probe was successful.

Fixes: a8837cf43839 ("dma: ti: k3-udma: Query DMA channels allocated from Resource Manager")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>