Currently in j721e_init.c we check which firewalls to remove using
the board configuration (e.g CONFIG_TARGET_J721E_R5_EVM). We do this
as J721e and J7200 have different IP and firewalls but use the same
SoC definition (SOC_K3_J721E) even though they are different SoCs.

The idea was they would be similar enough that they both could use
the same SoC config to help with common code sharing. Board checks
would then be used differentiate.

This has grown far too messy to maintain any more, especially now
that there is more than one board using J721e (EVM, SK, Beagle AI64).
As differentiation is done based on board, every one of these boards
would have to have checks added for them. Instead let's split J7200
support out from J721e like how normal new SoC support is done.

This patch touches several subsystems and could not be split much better
as when we add SOC_K3_J7200 we want to make use of it in all spots that
once used the combined SOC_K3_J721E so we can turn off SOC_K3_J721E when
building for J7200 boards.

Signed-off-by: Andrew Davis <afd@ti.com>

Greg Malysa <malysagreg@gmail.com> says:

This series adds all of the supported peripheral drivers for the sc5xx
series of SoCs from Analog Devices and other drivers that are used by
the evaluation kits, such as a GPIO expander used by the EZLITE carrier
boards. This series passes gitlab CI tests.

Link: https://lore.kernel.org/r/20250226173150.13198-1-malysagreg@gmail.com

Add a rudimentary MDMA driver for the Analog Devices SC5xx SoCs,
primarily intended for use with and tested against the QSPI/OSPI
IP included in the SoC.

Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>

During dma memcpy, bcdma descriptor gets allocated for each
transaction and not freed after completion of that transaction.
So, avoid the memory allocation for every transaction.

Add one descriptor per dma device and allocate it once in
resource setup. This descriptor can now be used for all
dma memcpy transactions optimally.

Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>

RFLOW config related MMR does not exist incase of BCDMA.
Add check to bypass the RFLOW MMR extraction.
Without this, the probe sequence fails checking for
the MMR_RFLOW region, which is valid only for packet based
DMA and obselete for BCDMA.

Fixes: 5abb694d6016 ("dma: ti: k3-udma: Add support for native configuration of chan/flow")
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>

Currently, the allocation of DMA channel[0] for memcpy is happening
in udma_transfer() for every transfer, which leads to a huge overhead
for each transfer, especially in case of nand page reads. So, move this
allocation to udma_probe(), as a result, the allocation is done once
during probe.

Introduce udma_remove() for the cleanup of allocated channel during
probe.

Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>

The udma_probe() function was placed above many important APIs
related to bcdma, pktdma, which restricts these APIs to be accessed
during probe. So, move udma_probe() below all of them.

Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>

In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup TCHAN/RCHAN/RFLOW cfg registers.
Existing UDMA driver performed the above mentioned configuration
for UDMA. Add similar configuration for PKTDMA here.

Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>

Drop all duplicate newlines. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>