u-boot.git/drivers/fastboot/Kconfig, branch v2023.04

fastboot: Add OEM run command

2023-01-11T20:02:24Z

This adds the UUU UCmd functionality as an OEM command. While the fastboot tool allows sending arbitrary commands as long as they are prefixed with "oem". This allows running generic U-Boot commands over fastboot without UUU, which is especially useful when not using USB. This is really the route we should have gone in the first place when adding these commands. While we're here, clean up the UUU Kconfig a bit. Signed-off-by: Sean Anderson Reviewed-by: Heiko Schocher

net: fastboot: make UDP port net: configurable

2022-01-15T16:54:21Z

The fastboot protocol uses per default the UDP port 5554. In some cases it might be needed to change the used port. The fastboot utility provides a way to specifiy an other port number to use already. fastboot -s udp:192.168.1.76:1234 boot fastboot.img Signed-off-by: Christian Gmeiner Reviewed-by: Heiko Schocher Reviewed-by: Ramon Fried

Kconfig: Remove all default n/no options

2021-08-31T21:47:49Z

default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini

fastboot: add UUU command UCmd and ACmd support

2021-02-26T14:30:55Z

add support for the UUU commands ACmd and UCmd. Enable them through the Kconfig option CONFIG_FASTBOOT_UUU_SUPPORT base was commit in NXP kernel 9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support") and ported it to current mainline. Tested this patch on imx6ul based board. Signed-off-by: Heiko Schocher Acked-by: Patrick Delaunay

fastboot: add command to select the eMMC boot configuration

2021-02-07T18:22:55Z

Add command oem bootbus which executes the command ``mmc bootbus `` on the current fastboot mmc device ( = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot configuration on first update, with = boot_bus_width reset_boot_bus_width boot_mode $> fastboot oem bootbus: Signed-off-by: Patrick Delaunay

fastboot: add command to select the default emmc hwpart for boot

2021-02-07T18:22:55Z
Add fastboot command oem partconf which executes the command ``mmc partconf 0`` on the current mmc device to configure the eMMC boot partition with : boot_ack boot_partition, so the command is: $> fastboot oem partconf: The partition_access argument is forced to 0 (userdata) Signed-off-by: Patrick Delaunay [lukma - Kconfig adjustments after merging this patch]

fastboot: mmc: extend flash/erase for both emmc hwpart 1 and 2

2021-02-07T18:22:55Z
Update the code and the configs for eMMC boot and userdata partitions acces - FASTBOOT_MMC_BOOT_SUPPORT: boot partition 1 and 2 (erase/write) - FASTBOOT_MMC_BOOT1_NAME: boot partition 1, default name="mmc0boot0" - FASTBOOT_MMC_BOOT2_NAME: boot partition 2, default name="mmc0boot1" This patch also removes the unnecessary dependency with ARCH_MEDIATEK and EFI_PARTITION. Signed-off-by: Patrick Delaunay

fastboot: mmc: Add CONFIG_FASTBOOT_MMC_USER_SUPPORT

2021-02-07T18:22:55Z
Split userdata and boot partition support for eMMC update and correct the description (update is supported). The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT allows to activate support of userdata partition update, based on target name=CONFIG_FASTBOOT_MMC_USER_NAME This patch also removes the unnecessary dependency with ARCH_MEDIATEK and EFI_PARTITION. Signed-off-by: Patrick Delaunay

Revert "fastboot: Add default fastboot_set_reboot_flag implementation"

2021-02-07T18:22:54Z
This reverts commit 0ebf9842e56c5b8cb7cb1f990bb452cc14af6225. Current generic implementation of fastboot_set_reboot_flag is somewhat messy and requires some additional configuration option to be enabled besides CMD_BCB, so it reverts that implementtion in order to bring a new cleaner one. Next commit introduces new generic implementation of fastboot_set_reboot_flag. Signed-off-by: Roman Kovalivskyi

fastboot: Add default fastboot_set_reboot_flag implementation

2020-09-01T12:47:43Z
Default implementation of fastboot_set_reboot_flag function that depends on "bcb" commands could be used in general case if there are no need to make any platform-specific implementation, otherwise it could be disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG. Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive with some platforms which already have their own implementation of this function. Signed-off-by: Roman Kovalivskyi