u-boot.git/drivers/fastboot/Kconfig, branch v2024.04

fastboot: add oem console command support

2024-01-09T13:58:33Z

"oem console" serves to read console record buffer. Signed-off-by: Ion Agorria Signed-off-by: Svyatoslav Ryhel Reviewed-by: Mattijs Korpershoek Link: https://lore.kernel.org/r/20240105072212.6615-7-clamor95@gmail.com Signed-off-by: Mattijs Korpershoek

fastboot: Depend on CMDLINE

2023-11-07T19:49:10Z

Much of the functionality of fastboot relies on being able to run commands as defined in the environment. This means it does depend on CMDLINE being enabled. Signed-off-by: Tom Rini

Kconfigs: Correct default of "0" on hex type entries

2023-08-09T13:21:42Z

It is not a parse error to have a default value of "0" for a "hex" type entry, instead of "0x0". However, "0" and "0x0" are not treated the same even by the tools themselves. Correct this by changing the default value from "0" to "0x0" for all hex type questions that had the incorrect default. Fix one instance (in two configs) of a default of "0" being used on a hex question to be "0x0". Remove the cases where a defconfig had set a value of "0x0" to be used as the default had been "0". Signed-off-by: Tom Rini Reviewed-by: Simon Glass

net: add fastboot TCP support

2023-05-05T21:48:44Z

Known limitations are 1. fastboot reboot doesn't work (answering OK but not rebooting) 2. flashing isn't supported (TCP transport only limitation) The command syntax is fastboot tcp Signed-off-by: Dmitrii Merkurev Cc: Ying-Chun Liu (PaulLiu) Cc: Simon Glass Сс: Joe Hershberger Сс: Ramon Fried Reviewed-by: Simon Glass

fastboot: Add OEM run command

2023-01-11T20:02:24Z

This adds the UUU UCmd functionality as an OEM command. While the fastboot tool allows sending arbitrary commands as long as they are prefixed with "oem". This allows running generic U-Boot commands over fastboot without UUU, which is especially useful when not using USB. This is really the route we should have gone in the first place when adding these commands. While we're here, clean up the UUU Kconfig a bit. Signed-off-by: Sean Anderson Reviewed-by: Heiko Schocher

net: fastboot: make UDP port net: configurable

2022-01-15T16:54:21Z

The fastboot protocol uses per default the UDP port 5554. In some cases it might be needed to change the used port. The fastboot utility provides a way to specifiy an other port number to use already. fastboot -s udp:192.168.1.76:1234 boot fastboot.img Signed-off-by: Christian Gmeiner Reviewed-by: Heiko Schocher Reviewed-by: Ramon Fried

Kconfig: Remove all default n/no options

2021-08-31T21:47:49Z

default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini

fastboot: add UUU command UCmd and ACmd support

2021-02-26T14:30:55Z

add support for the UUU commands ACmd and UCmd. Enable them through the Kconfig option CONFIG_FASTBOOT_UUU_SUPPORT base was commit in NXP kernel 9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support") and ported it to current mainline. Tested this patch on imx6ul based board. Signed-off-by: Heiko Schocher Acked-by: Patrick Delaunay

fastboot: add command to select the eMMC boot configuration

2021-02-07T18:22:55Z

Add command oem bootbus which executes the command ``mmc bootbus `` on the current fastboot mmc device ( = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot configuration on first update, with = boot_bus_width reset_boot_bus_width boot_mode $> fastboot oem bootbus: Signed-off-by: Patrick Delaunay

fastboot: add command to select the default emmc hwpart for boot

2021-02-07T18:22:55Z
Add fastboot command oem partconf which executes the command ``mmc partconf 0`` on the current mmc device to configure the eMMC boot partition with : boot_ack boot_partition, so the command is: $> fastboot oem partconf: The partition_access argument is forced to 0 (userdata) Signed-off-by: Patrick Delaunay [lukma - Kconfig adjustments after merging this patch]