u-boot.git/drivers/firmware, branch v2020.07-rc2

Merge tag 'xilinx-for-v2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

2020-04-07T21:13:35Z

Xilinx changes for v2020.07 common: - Align ENV_FAT_INTERFACE - Fix MAC address source print log - Improve based autodetection code xilinx: - Enable netconsole Microblaze: - Setup default ENV_OFFSET/ENV_SECT_SIZE Zynq: - Multiple DT updates/fixes - Use DEVICE_TREE environment variable for DTB selection - Switch to single zynq configuration - Enable NOR flash via DM - Minor SPL print removal - Enable i2c mux driver ZynqMP: - Print multiboot register - Enable cache commands in mini mtest - Multiple DT updates/fixes - Fix firmware probing when driver is not enabled - Specify 3rd backup RAM boot mode in SPL - Add SPL support for zcu102 v1.1 and zcu111 revA - Redesign debug uart enabling and psu_init delay - Enable full u-boot run from EL3 - Enable u-boot.itb generation without ATF with U-Boot in EL3 Versal: - Enable distro default - Enable others SPI flashes - Enable systems without DDR Drivers: - Gem: - Flush memory after freeing - Handle mdio bus separately - Watchdog: - Get rid of unused global data pointer - Enable window watchdog timer - Serial: - Change reinitialization logic in zynq serial driver Signed-off-by: Tom Rini

firmware: zynqmp: Enable IPI code calling also in EL3

2020-04-06T10:52:45Z

U-Boot proper can still run in EL3 without using firmware interface wired via ATF. For supporting this use case there is a need to check EL level where U-Boot runs and based on that choose the way how to talk to firmware. Signed-off-by: Michal Simek

firmware: tisci: Drop all deprecated messages

2020-03-03T07:38:14Z

SYSFW v2020.01 and later versions no longer supports the below messages: - TI_SCI_MSG_RM_RING_GET_CFG - TISCI_MSG_RM_UDMAP_TX_CH_GET_CFG 0x1206 - TISCI_MSG_RM_UDMAP_RX_CH_GET_CFG 0x1216 - TISCI_MSG_RM_UDMAP_FLOW_GET_CFG 0x1232 - TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_GET_CFG 0x1233 There are no users in U-Boot for any of the above messages, So drop the support for all the corresponding messages. Signed-off-by: Lokesh Vutla

dm: core: Create a new header file for 'compat' features

2020-02-06T02:33:46Z

At present dm/device.h includes the linux-compatible features. This requires including linux/compat.h which in turn includes a lot of headers. One of these is malloc.h which we thus end up including in every file in U-Boot. Apart from the inefficiency of this, it is problematic for sandbox which needs to use the system malloc() in some files. Move the compatibility features into a separate header file. Signed-off-by: Simon Glass

dm: core: Require users of devres to include the header

2020-02-06T02:33:46Z

At present devres.h is included in all files that include dm.h but few make use of it. Also this pulls in linux/compat which adds several more headers. Drop the automatic inclusion and require files to include devres themselves. This provides a good indication of which files use devres. Signed-off-by: Simon Glass Reviewed-by: Anatolij Gustschin

firmware: Remove probe which is causing extra bind

2020-01-14T08:05:55Z

Remove probe function dm_scan_fdt_dev from zynqmp-firmware driver. It is just binding its subnode zynqmp-clk. As a result one extra node is showing up in dm tree. This is not required, it is anyway bound from it's own zynqmp-clk driver. Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek

common: Move enable/disable_interrupts out of common.h

2019-12-02T23:25:01Z

Move these two functions into the irq_funcs.h header file. Also move interrupt_handler_t as this is used by the irq_install_handler() function. Signed-off-by: Simon Glass Reviewed-by: Tom Rini

firmware: zynqmp: Clean up zynqmp_power_probe

2019-10-24T11:37:01Z

Fix error debug messages to be more accurate and aligned with debug message style in the whole file. And do not initialize ret variable because it is initialized later on and it is just additional step. Fixes: 1327d1678bd2 ("firmware: zynqmp: Add zynqmp-power support") Reported-by: Luca Ceresoli Signed-off-by: Michal Simek Reviewed-by: Luca Ceresoli

firmware: zynqmp: Report error when xilinx_pm_request called from EL3

2019-10-24T11:37:01Z

Function should report error when called in EL3 context. Also report it as error instead 0 (success). Reported-by: Luca Ceresoli Signed-off-by: Michal Simek Reviewed-by: Luca Ceresoli

arm64: zynqmp: Convert invoke_smc() to xilinx_pm_request()

2019-10-24T11:37:01Z

Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to xilinx_pm_request() which do calculation with PM_SIP_SVC already. Signed-off-by: Michal Simek