For some reason, on the Mercury+ AA1 module, calling
fpgamgr_wait_early_user_mode immediately after writing the peripheral
bitstream leaves the fpga in a broken state (ddr calibration hangs).
Adding a delay before the first sync word is written seems to fix this.
Inspecting the fpgamgr registers before and after the delay,
imgcfg_FifoEmpty is the only bit that changes. Waiting for this bit
(instead of a hardcoded delay) also fixes the issue.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Apply some optimizations to speed up bitstream loading
(both for full and split periph/core bitstreams):

 * Change the size of the first fs read, so that all the subsequent
   reads are aligned to a specific value (called MAX_FIRST_LOAD_SIZE).
   This value was chosen so that in subsequent reads the fat fs driver
   doesn't have to allocate a temporary buffer in get_contents
   (assuming 8KiB clusters).

 * Change the buffer size to a larger value when reading to ddr
   (but not too large, because large transfers cause a stack overflow
   in the dwmmc driver).

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Double peripheral RBF configuration are needed on some devices or boards
to stabilize the IO configuration system.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Create common macro TARGET_SOCFPGA_SOC64 for Stratix10 and Agilex.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>

Xilinx changes for v2021.04-rc3

qspi:
- Support for dual/quad mode
- Fix speed handling

clk:
- Add clock enable function for zynq/zynqmp/versal

gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path

fpga:
- Fix buffer alignment for ZynqMP

xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name

Due to pointer arithmetic, "sizeof(u32) * ARCH_DMA_MINALIGN" is
subtracted. It seems that the original intention was to just subtract
ARCH_DMA_MINALIGN. Fix it.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.

For now no callers pass the size, but this can be updated later.

Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

In non-secure mode (EL2), FPGA reconfiguration driver calls the
SMC/PSCI services provided by ATF to configure the FPGA.

Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>