u-boot.git/drivers/gpio/Kconfig, branch v2017.09

Convert CONFIG_CMD_TCA642X to Kconfig

2017-08-11T19:42:00Z

This converts the following to Kconfig: CONFIG_CMD_TCA642X Signed-off-by: Simon Glass Reviewed-by: Bin Meng Reviewed-by: Philipp Tomsich

Convert CONFIG_CMD_PCA953X to Kconfig

2017-08-11T19:41:50Z

This converts the following to Kconfig: CONFIG_CMD_PCA953X Signed-off-by: Simon Glass Reviewed-by: Bin Meng Reviewed-by: Philipp Tomsich

x86: Convert INTEL_ICH6_GPIO to Kconfig

2017-08-01T12:17:02Z

This converts Intel ICH6 GPIO driver to Kconfig, and add it to the imply list of platform drivers. Signed-off-by: Bin Meng Reviewed-by: Simon Glass

gpio: Move OMAP_GPIO to Kconfig

2017-05-15T14:40:00Z

This driver is used often enough such that we want to have this enabled by default on any ARCH_OMAP2PLUS board, and this only compiles on ARCH_OMAP2PLUS due to required defines, so mark that as the depends. Signed-off-by: Tom Rini

dm: gpio: add BCM6345 gpio driver

2017-05-10T14:16:09Z

This driver is based on linux/arch/mips/bcm63xx/gpio.c, simplified to allow defining one or two independent banks for each Broadcom SoC. Signed-off-by: Álvaro Fernández Rojas Reviewed-by: Simon Glass

dm: gpio: Add driver for stm32f7 gpio controller

2017-05-08T15:57:02Z

This patch adds gpio driver supporting driver model for stm32f7 gpio. Signed-off-by: Vikas Manocha Reviewed-by: Simon Glass Cc: Christophe KERELLO [trini: Add depends on STM32] Signed-off-by: Tom Rini

gpio: Kconfig: add CONFIG_AT91_GPIO option

2017-04-13T20:44:50Z

The CONFIG_AT91_GPIO option is used to select AT91 PIO GPIO driver. Signed-off-by: Wenyou Yang Reviewed-by: Simon Glass Reviewed-by: Andreas Bießmann

gpio: Add Rapid GPIO2P driver for i.MX7ULP

2017-03-17T08:27:08Z

Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP. Have added all ports on RGPIO2P_0 and RGPIO2P_1. The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set to y to enable the drivers. To use the GPIO function, the IBE and OBE needs to set in IOMUXC. We did not set the bits in driver, but leave them to IOMUXC settings of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number for gpio APIs access. Signed-off-by: Peng Fan Signed-off-by: Ye Li Reviewed-by : Stefano Babic

gpio: atmel_pio4: Rework to support DM & DT

2016-08-15T20:58:03Z

Rework the driver to support driver model and device tree, and support to regard the pio4 pinctrl device as a child of atmel_pio4 device. Signed-off-by: Wenyou Yang Reviewed-by: Simon Glass

gpio: Add driver for TI PCF8575 I2C GPIO expander

2016-08-08T17:32:53Z

TI's PCF8575 is a 16-bit I2C GPIO expander.The device features a 16-bit quasi-bidirectional I/O ports. Each quasi-bidirectional I/O can be used as an input or output without the use of a data-direction control signal. The I/Os should be high before being used as inputs. Read the device documentation for more details[1]. This driver is based on pcf857x driver available in Linux v4.7 kernel. It supports basic reading and writing of gpio pins. [1] http://www.ti.com/lit/ds/symlink/pcf8575.pdf Signed-off-by: Vignesh R Reviewed-by: Tom Rini Reviewed-by: Simon Glass Reviewed-by: Mugunthan V N