u-boot.git/drivers/gpio, branch v2014.07-rc2

dm: rename device struct to udevice

2014-05-27T14:21:32Z

using UBI and DM together leads in compiler error, as both define a "struct device", so rename "struct device" in include/dm/device.h to "struct udevice", as we use linux code (MTD/UBI/UBIFS some USB code,...) and cannot change the linux "struct device" Signed-off-by: Heiko Schocher Cc: Simon Glass Cc: Marek Vasut

Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'

2014-05-15T15:19:45Z

ARM: tegra: add GPIO initialization table function

2014-05-13T17:41:31Z

The HW-defined procedure for booting Tegra requires that some pins be set up as GPIOs immediately at boot in order to avoid glitches on those pins, when the pinmux is programmed. Add a feature to the GPIO driver which executes a GPIO configuration table. Board files will use this to implement the correct HW initialization procedure. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren

S5P: Exynos: Add GPIO pin numbering and rename definitions

2014-05-13T06:20:38Z

This patch includes following changes : * Adds gpio pin numbering support for EXYNOS SOCs. To have consistent 0..n-1 GPIO numbering the banks are divided into different parts where ever they have holes in them. * Rename GPIO definitions from GPIO_... to S5P_GPIO_... These changes were done to enable cmd_gpio for EXYNOS and cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence getting a error during compilation. * Adds support for name to gpio conversion in s5p_gpio to enable gpio command EXYNOS SoCs. Function has been added to asm/gpio.h to decode the input gpio name to gpio number. Example: SMDK5420 # gpio set gpa00 Signed-off-by: Leela Krishna Amudala Signed-off-by: Rajeshwari Shinde Signed-off-by: Akshay Saraswat Acked-by: Przemyslaw Marczak Signed-off-by: Minkyu Kang

sandbox: Convert GPIOs to use driver model

2014-03-04T17:15:30Z

Convert sandbox over to use driver model GPIOs. Signed-off-by: Simon Glass

dm: Add GPIO support and tests

2014-03-04T17:15:30Z

Add driver model support for GPIOs. Since existing GPIO drivers do not use driver model, this feature must be enabled by CONFIG_DM_GPIO. After all GPO drivers are converted over we can perhaps remove this config. Tests are provided for the sandbox implementation, and are a sufficient sanity check for basic operation. The GPIO uclass understands the concept of named banks of GPIOs, with each GPIO device providing a single bank. Within each bank the GPIOs are numbered using an offset from 0 to n-1. For example a bank named 'b' with 20 offsets will provide GPIOs named b0 to b19. Anonymous GPIO banks are also supported, and are just numbered without any prefix. Each time a GPIO driver is added to the uclass, the GPIOs are renumbered accordinging, so there is always a global GPIO numbering order. Signed-off-by: Simon Glass Signed-off-by: Marek Vasut Signed-off-by: Pavel Herrmann Signed-off-by: Viktor Křivák Signed-off-by: Tomas Hlavacek

sizes.h - consolidate for all architectures

2014-03-04T17:15:01Z

Copied from Linux sources "include/linux/sizes.h" commit 413541dd66d51f791a0b169d9b9014e4f56be13c Signed-off-by: Alexey Brodkin Cc: Vineet Gupta Cc: Tom Rini Cc: Stefan Roese Cc: Albert Aribaud Acked-by: Tom Rini Acked-by: Stefan Roese [trini: Add bcm Kona platforms to the patch] Signed-off-by: Tom Rini

gpio: kona: Add Kona gpio driver

2014-02-22T18:30:27Z

Add support for the Kona GPIO controller found on Broadcom mobile SoCs. Signed-off-by: Darwin Rambo Reviewed-by: Steve Rae Reviewed-by: Markus Mayer Reviewed-by: Tim Kryger

s5p: gpio: change gpio coding method for s5p gpio.

2014-02-03T06:36:14Z

Old s5p gpio coding method was not clean and was not working properly for all parts and banks. New method is clean and easy to extend. Gpio coding mask: 0x000000ff - pin number 0x00ffff00 - bank offset 0xff000000 - part number Signed-off-by: Przemyslaw Marczak Signed-off-by: Minkyu Kang

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

2014-01-06T07:49:58Z

Conflicts: include/micrel.h The conflict above was trivial, caused by four lines being added in both branches with different whitepace.