u-boot.git/drivers/i2c/Makefile, branch v2018.09

i2c: Drop CONFIG_SH_SH7734_I2C

2018-05-23T21:30:04+00:00

Last user of this driver went away in May 2017 in commit
eb5ba3aefdf0f6c ("i2c: Drop use of CONFIG_I2C_HARD").

Signed-off-by: Tuomas Tynkkynen 
Acked-by: Heiko Schocher

i2c: Drop CONFIG_TSI108_I2C

2018-05-23T21:30:04+00:00

Last user of this driver went away in June 2015 in commit
d928664f4101e24 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")

Signed-off-by: Tuomas Tynkkynen 
Acked-by: Heiko Schocher

i2c: rcar_i2c: Add DM and DT capable I2C driver

2018-05-20T10:06:54+00:00

Add derivative of the rcar_i2c driver which is capable of
probing itself from DM and uses DT.

Signed-off-by: Marek Vasut 
Cc: Heiko Schocher 
Cc: Nobuhiro Iwamatsu

i2c: rcar_i2c: Remove the driver

2018-05-20T10:06:54+00:00

Remove the rcar_i2c driver, since it's no longer used by any
board and will be superseded by a DM and DT capable variant.

Signed-off-by: Marek Vasut 
Cc: Heiko Schocher 
Cc: Nobuhiro Iwamatsu

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini

i2c: rcar_iic: Add RCar IIC driver

2017-11-30T01:32:34+00:00

Add driver for the RCar IIC or DVFS I2C controller. This driver is based
on the SH I2C driver, but supports DM and DT probing as well as modern
I2C framework API.

Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu

i2c: add Amlogic Meson driver

2017-11-20T09:11:34+00:00

Add a driver for the I2C controller available on Amlogic Meson SoCs.

Signed-off-by: Beniamino Galvani 
Reviewed-by: Neil Armstrong

i2c: fti2c010: remove unused/unmaintained driver

2017-10-27T12:52:22+00:00

CONFIG_SYS_I2C_FTI2C010 is not enabled by anyone.

Commit 2852709676c8 ("dm: i2c: Add a note to I2C drivers which need
conversion") prompted to convert this driver to DM before June 2017,
but not converted yet.

Signed-off-by: Masahiro Yamada 
Acked-by: Heiko Schocher

i2c: adi_i2c: remove left-over Blackfin I2C driver

2017-10-27T12:52:22+00:00

This driver was used by Blackfin boards, but Blackfin support is
gone.  There is no user of this driver.

Signed-off-by: Masahiro Yamada 
Acked-by: Heiko Schocher

i2c: add i2c driver for stm32

2017-08-23T05:04:40+00:00

Add i2c driver which can be used on both STM32F7 and STM32H7.
This I2C block supports the following features:
 _ Slave and master modes
 _ Multimaster capability
 _ Standard-mode (up to 100 kHz)
 _ Fast-mode (up to 400 kHz)
 _ Fast-mode Plus (up to 1 MHz)
 _ 7-bit and 10-bit addressing mode
 _ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask)
 _ All 7-bit addresses acknowledge mode
 _ General call
 _ Programmable setup and hold times
 _ Easy to use event management
 _ Optional clock stretching
 _ Software reset

Signed-off-by: Christophe Kerello 
Signed-off-by: Patrice Chotard 
Reviewed-by: Simon Glass