The driver assumed that I2C1 and I2C2 were always enabled,
and if they were not, then an asynchronous abort was (silently)
raised, to be caught much later on in the Linux kernel.

Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4
are.

To make the change binary-invariant, declare I2C1 and I2C2 in
every include/configs/ file which defines CONFIG_SYS_I2C_MXC.

Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and
CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed
(CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE)
config options.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.

Please note that this patch also removes these config options:

- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT

As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.

If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.

Signed-off-by: Simon Glass <sjg@chromium.org>

This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

We have flipped CONFIG_SPL_DISABLE_OF_CONTROL.  We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:

 #ifdef CONFIG_OF_CONTROL
 # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
 #  define OF_CONTROL 0
 # else
 #  define OF_CONTROL 1
 # endif
 #else
 # define OF_CONTROL 0
 #endif

Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute.  It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.

Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

LPC32xx has 3 I2C bus controllers, 2 of them are used as generic ones
and their parent clock is HCLK and CLK_HI/CLK_LO registers are 10 bit
wide. This means that if HCLK is 104MHz, then minimal configurable I2C
clock speed is about 51KHz.

Only USB OTG I2C bus controller CLK registers are 8 bit wide, thus in
assumption that peripheral clock is 13MHz it allows to set the minimal
bus speed about 25.5KHz.

Check for negative half clock value is removed since it is always false.

The change fixes the following problem for I2C busses 0 and 1:

  => i2c dev 0
  Setting bus to 0
  => i2c speed 100000
  Setting bus speed to 100000 Hz
  Failure changing bus speed (-22)

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>

Updated the LPC32xx I2C driver to support
the OTG I2C that is part of the USB module.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>

Fix a condition that generate watchdog timeout inside "lpc32xx_i2c_write" when parameters alen = 0 and len = 0.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>

Fix a condition that generate watchdog timeout inside "lpc32xx_i2c_read" when parameters alen != 0 and len = 0.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>

The HCLK is not constant and can take different value; use the api function to get the value of the HCLK for the I2C clock high and low computation.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>