u-boot.git/drivers/misc/Kconfig, branch v2023.04

rockchip: efuse: Add support for RK3288 and more

2023-02-28T10:07:28Z

Add support for rk3066a, rk3188, rk322x and rk3288 compatible. Signed-off-by: Jonas Karlman Reviewed-by: Kever Yang

Convert CONFIG_SMSC_LPC47M et al to Kconfig

2022-12-05T21:08:37Z

This converts the following to Kconfig: CONFIG_SMSC_LPC47M CONFIG_SMSC_SIO1007 Signed-off-by: Tom Rini

Convert CONFIG_MXS_OCOTP to Kconfig

2022-12-05T21:07:13Z

This converts the following to Kconfig: CONFIG_MXS_OCOTP Signed-off-by: Tom Rini

Convert CONFIG_FSL_IIM to Kconfig

2022-12-05T21:06:43Z

This converts the following to Kconfig: CONFIG_FSL_IIM Signed-off-by: Tom Rini

misc: imx: S400_API: Move S400 MU and API to a common place

2022-07-26T09:29:00Z

Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400 MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL Signed-off-by: Ye Li Signed-off-by: Peng Fan

misc: nuvoton: Add host interface configuration driver

2022-07-06T22:34:16Z

add nuvoton BMC npcm750 host configuration driver Signed-off-by: Jim Liu

Convert CONFIG_SYS_FSL_SEC_MON et al to Kconfig

2022-07-05T21:04:00Z

This converts the following to Kconfig: CONFIG_SYS_FSL_SEC_MON CONFIG_SYS_FSL_SEC_MON_BE CONFIG_SYS_FSL_SEC_MON_LE Signed-off-by: Tom Rini

misc: nuvoton: Add NPCM7xx otp controller driver

2022-06-23T01:30:05Z

Add Nuvoton BMC npcm750 otp driver Signed-off-by: Jim Liu

Merge branch 'master' into next

2022-06-20T18:40:59Z

Merge in v2022.07-rc5.

arm: layerscape: Add sfp driver

2022-06-20T01:18:25Z

This adds a driver for the Security Fuse Processor (SFP) present on LS1012A, LS1021A, LS1043A, and LS1046A processors. It holds the Super-Root Key (SRK), One-Time-Programmable Master Key (OTPMK), and other "security" related fuses. Similar devices (sharing the same name) are present on other processors, but for the moment this just supports the LS2 variants. The mirror registers are loaded during power-on reset. All mirror registers must be programmed or read at once. Because of this, `fuse prog` will program all fuses, even though only one might be specified. To prevent accidentally burning through all your fuse programming cycles with something like `fuse prog 0 0 A B C D`, we limit ourselves to one programming cycle per reset. Fuses are numbered based on their address. The fuse at 0x1e80200 is 0, the fuse at 0x1e80204 is 1, etc. The TA_PROG_SFP supply must be enabled when programming fuses, but must be disabled when reading them. Typically this supply is enabled by inserting a jumper or by setting a register in the board's FPGA. I've also added support for using a regulator. This could be helpful for automatically issuing the FPGA write, or for toggling a GPIO controlling the supply. I suggest using the following procedure for programming: 1. Override the fuses you wish to program => fuse override 0 2 A B C D 2. Inspect the values and ensure that they are what you expect => fuse sense 0 2 4 3. Enable TA_PROG_SFP 4. Issue a program command using OSPR0 as a dummy. Since it contains the write-protect bit you will usually want to write it last anyway. => fuse prog 0 0 0 5. Disable TA_PROG_SFP 6. Read back the fuses and ensure they are correct => fuse read 0 2 4 Signed-off-by: Sean Anderson